Battery Warnings; Assistance Service - Peg-Perego Adventure HP Manual De Instrucciones

!"#$%&'($)*+,-.///0/12334//))/35/65/0))16466))+789%7)11

BATTERY WARNINGS

Battery charging must be carried out and supervised
by adults only.
Do not allow children to play with the battery.
CHARGING THE BATTERY
• Charge the battery according to the instructions
enclosed with the battery charger and never for
more than 24 hours.
• To avoid damage, the battery should be charged as
soon as the vehicle starts to lose speed.
• If the vehicle is left unused for a long time,
remember to charge the battery and to keep it
disconnected from the electrical system. Repeat
the recharge procedure at least once every three
months.
• The battery must not be charged upside-down.
• Do not forget about the battery which is being
charged! Check it from time to time.
• Only use the battery charger provided and the
original battery.
PEG PEREGO
• The battery is sealed and does not require
maintenance.
WARNING
• THE BATTERY CONTAINS CORROSIVE TOXIC
SUBSTANCES.
DO NOT TAMPER WITH IT.
• The battery contains acid-based electrolytes.
• Do not create direct contact between the battery
terminals, avoid strong impacts: risk of explosion
and/or fire.
• While charging, the battery produces gas. Charge
the battery in a well-ventilated environment, away
from sources of heat and flammable materials.
• The flat battery must be removed from the vehicle.
• It is not advisable to bring the battery into contact
with clothes, as it could damage them.
• Only use the recommended type of battery or an
equivalent type.
IF THERE IS A BATTERY LEAK
Protect your eyes. Avoid direct contact with the
electrolyte. Protect your hands.
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE CARE
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used. For repairs use only original
spare parts.
• do not accept any responsibility for
PEG PEREGO
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by
PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• If the vehicle is overloaded on steep slopes, the
overload cut-out will immediately disconnect the
power. If this happens,
. The electrical brake will be
ACCELERATOR
activated, slowing down the descent of the vehicle.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
PEG PEREGO

ASSISTANCE SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
REMOVE THE FOOT FROM THE
PROBLEMS?
CONSUMER
which you can find on
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Turn the vehicle upside down and insert the two
forward carriage pins into the two holes without
pushing.
2 • Check that the forward carriage is oriented as
shown in the figure and then push in completely
until engaged.
3 • Insert the steering rod with the end oriented as
shown in the figure (see detail in fig. 4).
4 • Cross-section showing path of steering rod.
A= wheel steering tie rods
B= battery compartment
C= dashboard
5 • Fit the roll-bar on the electronic module,
inserting the hollow part of the roll-bar onto
one of the teeth on the electronic module.
Arrange the roll bar in the correct position and
engage onto the second tooth (see fig. A)
6 • Position the group assembled as above on the
dashboard, as shown in the figure, sliding it onto
the steering rod and inserting the 2 ends into
their seatings.
7 • Rotate the group until the complete engagement
of the 2 forward teeth and the side tooth (see
figure).
8 • Unite the two parts of the steering wheel.
9 • Insert the steering wheel onto the steering rod,
lining up the respective holes.
10 • Fix the steering wheel with the appropriate
screw and nut. IMPORTANT: the nut fits into the
hexagonal hole and the screw into the round
hole.
11 • Unscrew the battery compartment on the top of
the electronic module.
12 • Insert two AA-size 1.5 V batteries - Not Included
into the battery housing, taking care to match
the correct polarity. When finished, close the
battery compartment cover and re-tighten the
screw.
13 • Insert a metal washer onto the pin of the
forward carriage, as shown in the figure.
14 • Fit one of the two front wheels taking care to
use the wheel indicated in figure A.
15 • Insert a self-locking washer on the device shown
in the figure. It is important that the tabs of the
self-locking washer are facing the inside of the
device (see detail A).
NOTE: the bag contains 8 self-locking washers, 4
of which should be kept as spares in the case of
breakage.
16 • Fix the wheel as shown in the figure, pushing the
self-locking washer completely down.
17 • Snap on the hub cover. Carry out the same
procedure as in figure 13 for the other front
wheel.
18 • Insert a self-locking washer on the device shown
in the figure. It is important that the tabs of the
self-locking washer are facing the inside of the
device (see detail A).
19 • Remove the grey protection caps on the ends of
the rear axle and insert the axle into the device,
as shown in the figure.
20 • Insert the axle into one of the rear wheels, taking
care to use the wheel indicated in figure A.
21 • Insert the axle and wheel completely into the
gear motor hole until it emerges from the
opposite side of the vehicle.
22 • Slightly rotate the wheel to match and engage
the gear motor and wheel pentagons (figure A
shows the incorrect engagement of the wheel).
23 • Use the device as before to fix the next wheel.
Position the vehicle on its side with the wheel
downwards. Take care that the device does not
move.
24 • Insert a self-locking washer onto the device
shown in the figure. It is important that the tabs
of the self-locking washer are facing the inside of
the device (see detail A). Fix the wheel as shown
in the figure, pushing the self-locking washer
completely down. Snap on the remaining hub
covers on both sides.
25 • Fit the panel (which is found under the hood) on
the back of the vehicle, taking care to engage it
at the three points indicated with the three small
arrows.
26 • Before positioning the seat, check that the motor
wires are correctly connected.
27 • Position the seat, inserting the two rear