DeWalt D55154 Manual De Instrucciones página 13

8. Allow ample time for all oil to drain out. (Tilting
the compressor towards the drain plug will assist
in draining.)
9. Install the oil drain plug.
10. Fill pump using SAE 5W-40 full synthetic oil.
11. Replace dipstick.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
•
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
•
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states
or provinces.
In addition to the warranty, D
by our:
D WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
after purchase.
If you are not completely satisfied with the performance of
your D
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
WALT
lATin AMERiCA: This warranty does not apply to products
e
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
WALT Industrial
labels become illegible or are missing, call 1-800-4-D
e
(1-800-433-9258) for a free replacement.
Glossary
CFM: Cubic feet per minute.
sCFM: Standard cubic feet per minute; a unit of measure of
air delivery.
Psi: Pounds per square inch; a unit of measure of pressure.
kPa (kilopascal): Metric pressure measurement.
1 kilopascal equal 1000 pascals.
WALT factory
e
Code Certification: Products that bear one or more of the
following marks: UL, CUL, ETL, CETL, have been evaluated
by OSHA certified independent safety laboratories and
meet the applicable Underwriters Laboratories Standards
for Safety.
Cut-in Pressure: While the motor is off, air tank pressure
drops when accessory is used. When the tank pressure
drops to a certain low level the motor will restart
automatically. The low pressure at which the motor
automatically restarts is called cut-in pressure.
Cut-Out Pressure: When an air compressor is turned on
and begins to run, air pressure in the air tank begins to
build. It builds to a certain high pressure before the motor
automatically shuts off, protecting your air tank from
pressure higher than its capacity. The high pressure at which
the motor shuts off is called cut-out pressure.
Branch Circuit: The circuit carrying electricity from
electrical panel to outlet.
e
WALT tools are covered
e
1 YEAR FREE sERViCE
90 DAY MOnEY BACK gUARAnTEE
WALT Power Tool, Laser, or Nailer for any reason, you
e
English
WALT (1-800-433-9258).
WALT
e
11