Special Instructions - Dimas MX 160 F Manual De Instrucciones

This symbol indicates that the
machine is in conformance with
the applicable European directive.
MANDATORY
WARNING
These signs give advice
concerning your safety
Instruction plate
TYPE
MX 160 F
NOMINAL 230 V ~ 40-60
VOLTAGE
0 - 400 min - 1
OPERATING
SPEED

SPECIAL INSTRUCTIONS

The mixer is designed to operate safety and
reliaby when used according to the
instructions. To avoid danger to the
operator and maintain the mixer in good
working order, regular inspections should
be carried out on site. Check :
• Perfect technical condition (use for the
purpose for which it is intended and
taking into account any risks, and
correction of
detrimental to safety).
• Competent staff (qualifications, age,
training) who
understood the manual in detail
before starting work : any electrical,
mechanical or other problem should
be investigated by a qualified
maintenance engineer (electrician,
maintenance manager, approved
dealer, etc . . .).
• That the warnings and instructions
marked on the machine are followed
(adequate personal protection, correct
use, general safety instructions, etc).
• That no modification, transformation
or addition is detrimental to safety and
that it is carried out without prior
authorization from the manufacturer.
• Respect of the maintenance intervals
and periodical checks recommended.
• That only genuine spare parts are
used for repairs.
FAILURE TO COMPLY WITH
THESE WARNINGS
RESULT IN DEATH OR SERIOUS
7
BODILY INJURY.
• Read the instructions carefully and ensure
INDICATION
that you have understood them before
INFORMATION
using the machine.
INSTRUCTION
• Always keep the safety devices in
PROHIBITION
position.
• Always wear the approved ear and/or eye
protectors, helmet and breathing
apparatus.
• Store the machine properly. The machine
must be stored in a dry, locked place, out
of the reach of children.
SERIAL
• Know how to stop the machine quickly in
70001 1600W RATING
an emergency.
TOOL
IP 20 M 14
ENVIRONMENTAL
PROTECTION
• Check the machine, cable and plug before
6,3kg
use.
WEIGHT
FREQUENCY (Hz)
• Only have the machine repaired by a
specialist.
• Use the appropriate machine. Do not use
machines that are not powerful enough
and do not use adapters for heavy work.
• Wear suitable clothing. Do not wear
jewellery : they might get caught in
moving parts.
• Wear gloves and non-slip shoes when
working outdoors.
• Use a dust extractor and wear a dust
mask (dust is a health hazard).
• Keep the handles dry and free of oil and
grease.
any malfunction
• Always take care. Watch what you are
doing. Act sensibly.
have read and
• Do not use equipment or tools that are
damaged.
• Do not operate the machine in areas
where there are combustible materials.
• Do not plug in if the switch is not off.
• Do not use the machine in wet conditions.
• Do not allow people under 16 years old to
operate the machine.
• Do not use tools for work for which they
are not designed.
• Do not carry the machine by the cable. Do
not pull the cable to unplug. Protect the
cable from heat, petrol and sharp edges.
• Do not leave the machine unattended
while the motor is running.
COULD
• Do not use the machine if you are under
the influence of alcohol or drugs.
DO' S
• Application : mixing construction
• Tool : mixers with M14 internal thread.
• Rating : 1100 W
• Nominal voltage : 230 V
• Frequency : 40-60 Hz
• Operating speed : 0 to 580 rpm
• Tool - Ø max : 160 mm
• Interference
• Electrical protection : Class II
• Environmental protection : IP20
• Net weight : ca 6.3 kg
• Noise level : Based on DIN 45649 part 2
DON'TS
1 Use
materials.
2 Technical specifications
suppression
accordance with EN 55014 and EN6160
- DIN 45635 part 21 and DIN EN 27574
(ISO 7574)
s Noise level (LwAc) (94+3) dB rel 1pW
Operator noise level (LpA) 86 dB
Off load in accordance with DIN 45635
- 21 - KL2
s Noise level (LwAc) 88 dB rel 1pW
Operator noise level (LpA, cyclic) 79 dB
Under load (without working the part to
be machined) in accordance with DIN
45000 standards
3
Check before starting
Please read the instructions for
use prior to operating the
machine for the first time.
Motor off.
The working area must be
completely cleared, well lit and
all safety hazards removed (no
water or dangerous objects in
the vicinity).
The operator must wear
protective
appropriate to the work he
is doing. We recommend
that this includes both eye
and ear protection.
The use of ear protection is
mandatory.
Any persons not involved in the
work should leave the working
area.
: in
clothing