Electrical Safety - Dimas MX 160 F Manual De Instrucciones

4 Electrical connection

- ELECTRICAL SAFETY :

Operate this machine only on a
supply equipped with a 30 mA
earthed current-limiting circuit-
breaker. Otherwise, consult our
catalogue for appropriate models.
- The RCCB must be used
correctly, including testing it
regularly. For tools supplied
with an integral RCCB in the
cable or in the mains plug, if
the cable or plug has been
damaged, repairs must be
carried out
manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
• Motor power supply : reinforced electric
cable with 4 (3xPx+xE)
(3xPx+xNx+xE) conductors 2.5 mm
lengths less than 100 m.
• Earthing of the machine (mandatory).
5 Fitting the tool
Motor off
Disconnect by removing the plug.
• Mixers have an M14 internal thread.
Keep the thread and the external
surfaces clean.
• If the mixer becomes loose, tighten with a
22 mm open ended spanner
• Clean your tools thoroughly to work better
and more safely.
6 Starting
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from
machine
The machine has an electronic speed
control which prevents material flying when
the machine is turned on.
The speed may be controlled by varying the
pressure exerted on the controls.
• Momentary action switch :
On : press the switch
s
Off : release the switch
s
• Latching switch :
On : press the switch and latch it using
s
the button
Off : press the switch again and
s
release it
• During operation, always hold the
machine in both hands and work in a
stable position.
• Protect yourself against electrical
discharge. Do not touch equipment that is
earthed such as conduits, radiators . . .
by the
• Always keep the machine cable behind
you.
or 5
2 for
7 Important advice
• Retighten the bolts regularly, in particular
after the first hours of use.
The manufacturer declines all
responsibility for loss or damage
resulting from misuse or any
modification,
powering that does not conform
to the manufacturer's original
specifications.
At the work station, the sound
pressure level may exceed 85 db
(A)
In this case individual protection
measures must be taken.
8 Servicing and maintenance
The machine is designed to require only
minimum servicing and maintenance.
Make sure that the following points are
observed :
• Keep the machine clean.
• Do not allow any foreign body to
penetrate into the electrics.
• After about every 300 hours of use have
the brushes inspected by a specialist. If
they are less than 5 mm long, replace
with new brushes. The brushes should be
operated off load for about 20 minutes.
• At the same time, also check the
condition of the commutator. If the blades
are not uniform in colour and there are
floor and
surface stripes, the machine should be
sent to an approved workshop.
• The gear box and drive shaft should be
cleaned after 500 hours of operation.
• At this stage, the whole machine requires
servicing and should be sent to an
approved workshop.
9 Repairs
Contact your supplier who is
S
entirely at your service to carry
A
V out repairs in the shortest time at
the best possible price.
10 Spare parts
For rapid delivery of spares and in order to
avoid any wasted time, it is necessary to
remind your supplier of the details shown
on the instruction plate on the machine with
each order, as well as the reference of the
part to be replaced.
alteration or
11 Scrapping
In the event of deterioration and
scrapping of the machine, the
following
disposed of in accordance with
the
legislation in force.
• Main materials :
Motor : Aluminium (AL) - Steel (AC),
s
Motor :
Machine : Steel sheet (AC) -
s
€ Machine :
€ Machine :
The instructions for use and spare
parts found in this document are for
information only and are not binding.
As part of our product quality
improvement policy, we reserve the
right to make any and all technical
modifications without prior notice.
items must
requirements of the
Copper (CU) - Polyamide (PA)
Cast iron (FT) -
Aluminium (AL)
be
8