Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4. Connect the remote control.
5. Connect the IEC mains plug and power up
5. Connect the IEC mains plug and power up
6. Heat up time is usually between 2-3 minutes. Please ensure no button is
6. Heat up time is usually between 2
pressed during the heat up time. When the machine is ready the LED light on
pressed during the heat up time. When the machine is ready the LED light on
pressed during the heat up time. When the machine is ready the LED light on
the machine and remote control will illuminate.
the machine and remote control will illuminate.
7. After heat up, please refer to page 5"Operation for
After heat up, please refer to page 5"Operation for SFF-2".
CAUTION! TO PREVENT MORTAL ELECTRICAL RISK AND LONG LIFE OPERATION
TO PREVENT MORTAL ELECTRICAL RISK AND LONG LIFE OPERATION
TO PREVENT MORTAL ELECTRICAL RISK AND LONG LIFE OPERATION:
For your safety, please kindly pay attention to all of the warnings listed below:
For your safety, please kindly pay attention to all of the warnings listed below:
For your safety, please kindly pay attention to all of the warnings listed below:
1. Always plug in the power plug last and disconnect from the mains when the
1. Always plug in the power plug last and di
device is not in use or before cleaning.
device is not in use or before cleaning.
2. Do not install and operate the device in rain or extreme heat, moisture or dusty
2. Do not install and operate the device in rain or extreme heat, moisture or dusty
2. Do not install and operate the device in rain or extreme heat, moisture or dusty
environments.
3. This device is for indoor use only and in a dry environment.
3. This device is for indoor use only and in a dry environment.
4. Do not switch on immediately but wait until it reaches to room temperature if
immediately but wait until it reaches to room temperature if
immediately but wait until it reaches to room temperature if
the device has been exposed to drastic temperature fluctuations.
the device has been exposed to drastic temperature fluctuations.
5. Do not shake the device and avoid brute force when installing or operating.
5. Do not shake the device and avoid brute force when installing or operating.
5. Do not shake the device and avoid brute force when installing or operating.
6. Do not use the device during thunderstorms and please disconnect the power.
6. Do not use the device during thunderstorms and p
7. Do not use solvents or aggressive detergent to clean the device. Use a soft and
7. Do not use solvents or aggressive detergent to clean the device. Use a soft and
7. Do not use solvents or aggressive detergent to clean the device. Use a soft and
clean cloth.
8. Do not modify the device or the connected power cord without authorisation.
Do not modify the device or the connected power cord without authorisation.
Do not modify the device or the connected power cord without authorisation.
SELF-CLEANING FUNCTION:
CLEANING FUNCTION:
After use, please don't turn off the machine immediately.
The machine has self-cleaning function, there has 3 different right operations:
cleaning function, there has 3 different right operations:
cleaning function, there has 3 different right operations:
1. If use dmx-512, please turn the haze output to zero/turn off haze output, then still let the
512, please turn the haze output to zero/turn off haze output, then still let the
512, please turn the haze output to zero/turn off haze output, then still let the
power on about 80-90 seconds.
90 seconds.
2. If use digital display control, please turn the
splay control, please turn the "h" to "0", then still let the power on about 80
90 seconds.
3. If use timer remote, please turn the haze output to zero/turn off haze output, then still let
3. If use timer remote, please turn the haze output to zero/turn off haze output, then still let
3. If use timer remote, please turn the haze output to zero/turn off haze output, then still let
the power on about 80-90 seconds.
After this operation, the heater will be cleaned by air pump technology alter use.
After this operation, the heater
This is very important notice to maintain SFF-2 Haze machine!
This is very important notice to maintain
CONNECT WITH POWER SUPPLY – THE GROUND WIRE MUST BE CONNECTED
CONNECT WITH POWER SUPPLY
plug to connect to the main power supply as follows:
plug to connect to the main power supply as follows:
Wire
Brown
Blue
Yellow /Cyan
te control.
3 minutes. Please ensure no button is
sconnect from the mains when the
off the machine immediately.
90 seconds.
THE GROUND WIRE MUST BE CONNECTED:
Connection
Live
Neutral
Earth
10
lease disconnect the power.
0", then still let the power on about 80-
W i r e C o n n e c t i o n
C o n n e c t i o n
L
N
use.
Use the
Publicidad
Tabla de contenido
