Care And Maintenance - Inglesina Huggy Multifix Manual De Instrucciones

HUGGY MULTIFIX CAR SEAT
fig. 1
H1 Handle
H2 Handle adjustment buttons
H3 Belt release red button
H4 Reducer
H5 Hood
H6 Rear belt guide
H7 Rear release lever
HUGGY SHP BASE
fig. 2
HUGGY ISOFIX BASE
fig. 3
I1 Red/green indicators for base hooking on the car seat
I2 Isofix connectors
I3 Release lever
HANDLE ADJUSTMENT
fig. 4 To adjust the seat unit handle (H1), press
simultaneously the two buttons (H2) and rotate it to the
wished position. Make sure that the two buttons (H2)
completely come out, after having arranged the handle to
the proper position.
fig. 5 The handle of the seat unit can be adjusted to 4
different positions:
a) transport
b) intermediate
c) stability
d) car
To obtain the "car" configuration, rotate the handle to the
most forward position.
ADJUSTMENT OF THE SAFETY BELTS
fig. 6 Loosen the safety belts by pressing on the regulator
(A) and simultaneously pull them towards the internal side of
the seat unit. Place the child in the seat unit with the back
and legs completely in contact with the seat unit.
fig. 7 Verify that the safety belts are inserted in the
eyelets at the height of the shoulders (B) or immediately
above.
fig. 8 If the position is not correct, extract the belts from
the rear side of the seat unit and reinsert them in the second
pair of eyelets; always use eyelets at the same height.
fig. 9 Overlap the two ending parts (C) and insert them
in the buckle (D) until hearing the blocking CLICK. Verify the
correct closing by pulling the ends of the belts.
fig. 10 Let the belts adhere to the child's body, by pulling
its end on the regulator (A). A finger should not pass between
the belts and the child's body. To loosen the same, see Fig. 6.
fig. 11 To release the belts, press the red button (H3).
USE OF THE REDUCER
fig. 12 The seat unit is equipped with a reducer (H4) to
be used for children up to about 3 months of age. When the
reducer is used, make sure that the belts are positioned in the
lowest eyelets of the backrest.
USE OF THE HOOD
fig. 13 The seat unit is equipped with an adjustable hood
(H5). To hook it, insert the end (E) in the proper opening (F)
and let the fabric rear side adhere to the seat unit backrest. To
adjust it, simply accompany it to the wished position.
To remove the hood (H5), extract it firmly from the structure.
CAUTION: the hood shall not be used to lift the seat unit:
hazard of detachment.
INSTRUCTIONS

CARE AND MAINTENANCE

It is recommended to remove the lining periodically to
provide for its correct maintenance.
fig. 14
detach the lining from the structure by releasing the upper
(G) and lower (H) hooks from their seats.
fig. 15
fig. 16
then, remove the entire lining.
INSTALLATION ON BOARD WITHOUT BASE
Verify that on the seat of the car there are not any items that
may hinder the correct leaning of the Huggy Multifix car seat.
Verify that the backrest is in vertical position and the seat
where the seat unit has to be installed is NOT EQUIPPED
WITH FRONT AIRBAG.
Install the Inglesina car system only IN THE OPPOSITE
DIRECTION TO THE DRIVING ONE.
fig. 17
position. Make sure that the two buttons (H2) completely
come out, after having arranged the handle to the proper
position.
fig. 18
through the lateral seats (I).
fig. 19
fig. 20
through the rear guide (H6).
CAUTION: make sure that the safety belts are well
stretched and not twisted. Only in this way it is possible
to obtain the perfect anchoring of the Inglesina Huggy
car system.
INSTALLATION ON BOARD WITH BASE
Verify that on the seat of the car there are not any items that
may hinder the correct leaning of the car base to the seat.
Verify that the backrest is in vertical position and the seat
where the car base has to be installed is NOT EQUIPPED
WITH FRONT AIRBAG.
HUGGY SHP BASE
Install the Huggy SHP base on board of the car referring to
the dedicated manual.
fig. 21
base only IN THE OPPOSITE DIRECTION TO THE DRIVING
ONE, until hearing both CLICK sounds indicating the
occurred hooking.
CAUTION: make sure that the seat unit is properly hooked
on both sides.
fig. 22
forward position. Make sure that the two buttons (H2)
completely come out, after having arranged the handle to
the proper position.
fig. 23
through the rear guide (H6).
CAUTION: make sure that the safety belts are well
stretched and not twisted. Only in this way it is possible
to obtain the perfect anchoring of the Inglesina Huggy
car system.
REMOVAL OF THE HUGGY SHP BASE
fig. 24
position. After having removed the diagonal segment of the
safety belt from the rear guide (H6), act on the seat unit lever
(H7) and simultaneously lift it from the Huggy SHP base by
holding it by the handle.
Bring the handle (H1) to the most rear position;
Extract the protections from the belts.
Extract the belts from the suitable eyelets and,
Rotate the handle (H1) to the most forward
Pass the lower segment (K) of the car safety belt
Hook the car safety belt properly.
Pass the diagonal segment (L) of the car safety belt
Hook the Huggy Multifix car seat to the Huggy SHP
Rotate the seat unit handle (H1) to the most
Pass the diagonal segment (L) of the car safety belt
Rotate the seat unit handle (H1) to the vertical
21 21