Actuator - Setup - IVAR EQUICALOR DC 1010 Manual De Instrucciones

TECHNICAL SECTION
operation (See 'Signals' on pg. 20). Now proceed with the
test; see the following paragraph.
Verifying correct association
When the association procedure is complete, on the chron-
othermostat carry out the 'Identify actuator' function. See
Diagnostics (Identify actuator)
Managing the actuators
For correct system operation, the room in which the chron-
othermostat is installed MUST by defined as Zone1.
The system is able to manage up to a maximum of 28 ac-
tuators, which can be distributed in 8 zones. If one of the
actuators must be replaced, simply associate a new one
following the procedure described, up to a maximum of 4
replacements. If this new number of devices is reached,
carry out the procedure below before associating new ac-
tuators.
1) Perform 'Total device reset'.
2) Associate all the actuators (up to a maximum of 28).
 3.2
ACTUATOR – SETUP
Signals
The types of signals that the
listed below:
LED INDICATOR: FLASHING SIGNALS
Type of signal A*
à
Led 1
µ
Led 2
µ
Led 3
µ
Led 4
µ
Led 5
µ
Led 6
µ
• A* ACTIVE - rapid simultaneous flashing of the central
leds (LEDs 3 and 4), repeated 3 times.
• S* SEARCH - rapid movement of flashing from the cen tre
Led flash-
ing
LED 1 (1) Service
LED 2 (2) Anti-condensation function
LED 3 (3) Hysteresis [°F]
LED 4 (4) Maximum aperture
LED 5 (5) Corrective position
LED 6 (6) Proportional coefficient
on pg. 19.
Led Indicator can produce are
S* C* T1* T2*
µ µ µ µ
µ µ µ µ
µ µ µ µ
µ µ µ µ
µ µ µ µ
µ µ µ µ
TABLE 2: PARAMETER SELECTION
Parameter
[20]
300546US-10-14
(LED 3 and 4) to the ends (LED 1 and 6), repeated 3 times.
• C* CONFIRM - all leds flash for 1 second, repeated 3 times.
• T1* OPENING TEST - rapid simultaneous flashing of LEDs
1, 2 and 3 (repeated 3 times).
• T2* CLOSING TEST - rapid simultaneous flashing of LEDs
4, 5 and 6 (repeated 3 times).
• ANOMALY - in case of active alarms, the indicator com-
municates the following warnings at each touch of the
front selector. L BATT (Led 3 and 4 on) - L SIGN (Led 2 and
5 on) - ERR TE (Led 1 and 6 on). See 'Diagnostics (Alarm
History)' on pg. 18.
Options setup (selection and editing)
1) PARAMETER SELECTION (see Table-2)
To begin setting the parameters, maintain the front selec-
tor in the SELECT position until LEDs 1 and 6 which happens
after 20 seconds.
Release the button after this signal. Adjust the front selec-
tor in the '+' or '-' direction to scroll through the param-
eters from 1 to 6, indicated by the flashing led lights.
To proceed with setting the selected parameter, maintain
the selector in the SELECT
which happens after 5 seconds. Release the key after this
signal (a period of 60 seconds of inactivity or pressing in po-
sition SELECT for 20 seconds, completes the programming).
TABLE 3: EDITING THE PARAMETERS
(1) (2)
Parameter
à
Srv Acd
LED 1 -
LED 2 -
LED 3 -
LED 4 A
LED 5 B
LED 6 C
Abbre-
Default
viation
Srv C
Acd C
Ist 0.2
Pmax 8
Cp 3
Kp 0,10
position until Leds 3 and 4 light up,
(3) (4) (5)
Ist Pmax Cp
[°F]
- 1.2 13 7
- 1.0 11 6
- 0.8 9 5
- 0.6 8 4
B 0.4 7 3
C 0.2 6 2
Minimum Maximum
- -
- -
0.2 1.2
6 13
2 7
0,01 0,20
(6)
Kp
0,20
0,15
0,10
0,06
0,03
0,01