System Replacement Parts; System Installation - Honeywell MILLER Vi-Go Serie Manual De Isntrucciones

4.3 System Replacement Par ts
Part
Component
No.
TRTB Top Bracket Assembly
TRTB-7 7 ft. (2m) Top Bracket
Assembly
TRTB-10 10 ft. (3m) Top Bracket
Assembly
TRRCA Extra Rung Clamp Assembly
(for 5 ft. top bracket)
TRRCA-10 Extra Rung Clamp Assembly
(for 7ft. & 10 ft. top brackets)
TRLL Cable Lifeline
TRQL Quick Link
VGCG Automatic Pass-Through
Cable Guide
TRCG Manual Pass-Through
Cable Guide
TRBB Bottom Bracket Assembly
Model
No.
VGCS Vi-Go Automatic Pass-Through Cable Sleeve [Also available with carabiner (VGCS-C) or with integral swivel and carabiner (VGCS-SC)]
TRCS Vi-Go Manual Pass-Through Cable Sleeve [Also available with carabiner (TRCS-C) or with integral swivel and carabiner (TRCS-SC)]

5.0 System Installation

(see 8.0 Inspection and Maintenance). Do not use if there are any damaged or missing parts (see 4.3 System
Replacement Parts).
resulting from a fall (see 3.0 System Requirements).
separately. Contact your Miller distributor.
WARNING: Personal fall protection is required during installation.
Persons installing the system must use caution and shall not be
exposed to a fall hazard during the installation procedure. Do not
connect to any component of a partially installed system.
System Installation Overview: The recommended installation procedure of the Vi-Go Vertical Cable Lifeline
System is to install from the top of the ladder down.
Tools Required for Installation: Torque wrench, standard sockets--7/8" and 3/4", deep socket--9/16", standard
wrenches--7/16", 11/16" and 3/4", crowfoot wrench--17mm (for part VGCG only), cable cutters--minimum 3/8"
capacity needed (5/8" capacity preferred), and a tape measure.
Us er Instruct i o n s - E n g l i sh
5 ft. (1.5m) galvanized steel bracket (1-1/2" x 1-1/2" tube) includes inline shock absorber with shackle, two rung clamp
assemblies (each w/4-hole mounting plate for 1-1/2" tube, two 3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and
four 3/8"-16 hex nut fasteners), and bottom rung clamp assembly (w/3/8"-16 x 1-5/8" x 3-1/2" U-bolt, two 3/8" lockwashers,
two 3/8"-16 hex nut fasteners and two fastener caps).
7 ft. (2m) galvanized steel bracket (2" x 2" tube) includes inline shock absorber with shackle, two rung clamp assemblies
(each w/4-hole mounting plate for 2" tube, two 3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and four 3/8"-16 hex
two 3/8" lockwashers, and two 3/8"-16 hex nut fasteners).
10 ft. (3m) galvanized steel bracket (2" x 2" tube) includes inline shock absorber with shackle, two rung clamp assemblies
(each w/4-hole mounting plate for 2" tube, two 3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and four 3/8"-16 hex
two 3/8" lockwashers, and two 3/8"-16 hex nut fasteners).
Includes 4-hole mounting plate for 1-1/2" tube, two 3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and four 3/8"-
16 hex nut fasteners
Includes 4-hole mounting plate for 2" tube, two 3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and four 3/8"-16
hex nut fasteners
3/8" diameter galvanized steel cable with thimble. Various lengths available.
Galvanized steel quick-link used for connecting cable to shackle on inline shock absorber.
1.5mm locknuts.
Galvanized steel cable bracket with convertible polyurethane cable retainer head includes 3/8"-16 x 1-1/4" x 2" U-Bolt, two
Galvanized steel bracket (1-1/2" x 1-1/2" tube) includes rung clamp assembly (w/4-hole mounting plate for 1-1/2" tube, two
3/8"-16 x 1-5/8" x 3-1/2" U-bolts, four 3/8" lockwashers, and four 3/8"-16 hex nut fasteners), bottom rung clamp assembly
fasteners), and tensioning rod assembly (w/compression spring, two saddle clips, 7/16" washer, and six 7/16"-14 hex nut
fasteners).
Description
Cable Sleeve
may be purchased
8
TRIK