Maintenance; Periodic Maintenance; Troubleshooting - PLYMOVENT CONTROL PRO Manual De Instalación

6.2 use
6.2.1 Panel
Depending on the specific configuration and system settings
on the HMI, you can activate the fan and cleaning system
manually or have the entire system run fully automatically.
Manually activated functions:
Fig. 6.1
- green button START/STOP FAN (F)
- black button FILTER CLEANING (G)
You can activate START/STOP FAN and FILTER
CLEANING on the HMI as well.
To suppress the buzzer (I) in case of a WARNING signal (C),
push and hold the black button (G) for 5 seconds
6.2.2 HMI
The HMI shows the actual system status at all times.
If desired, you can activate the fan and the filter cleaning
system manually.
Refer to the online user manual ControlPro for
extensive explanation:
www.plymovent.com/manuals/controlpro
ControlPro/HMI
EN User manual
NL Gebruikershandleiding
DE Betriebsanleitung
FR Manuel opérateur
ES Instrucciones para el uso
www.plymovent.com/manuals/controlpro
7

MaiNtENaNcE

7.1

periodic maintenance

The indicated maintenance intervals can vary depending on
the specific working and ambient conditions. Therefore, we
recommend to thoroughly inspect the complete system once
every year beside the indicated periodic maintenance. For this
purpose contact your supplier.
WaRNiNg
If applicable, put the Panel in the Service Mode
before you do the activities as stated below; refer to
Fig. 6.1H.
38. You cannot stop/interrupt the filter cleaning cycle
39. You cannot activate this button during the first 40 running hours of the system
and within 40 running hours after filter replacement, to maintain the protective
layer of precoat material on the filter cartridges
40. You must still solve the cause of the warning
0000112606/200917/0 ControlPro
38 39
.
40
Component action
Panel Clean the outside with a
non-aggressive detergent
Make sure that the cable
glands are correctly tightened
Make sure that all detachable
screw terminal blocks on the
PC board are connected
HMI Clean with a non-aggressive
detergent
Make sure that the HMI cable
is connected
Check for firmware updates;
refer to the online user
manual
For maintenance of the connected filter system, fan and
other components, refer to the corresponding manuals.
8

tRouBLEShootiNg

If the system does not function (correctly), consult the
checklist below to see if you can remedy the error yourself.
Should this not be possible, contact your supplier.
WaRNiNg
If applicable, put the Panel in the Service Mode
before you do the activities as stated below; refer to
Fig. 6.1H.
Symptom problem
panel
Yellow Refer to HMI
WARNING
LED is on
(with or
without
buzzer)
Red ALARM Fan stops
LED is on +
Filter cleaning
buzzer
stops
hMi
HMI screen is No control on
locked HMI possible
Black screen HMI does not
function
No Configuration
installation of the system
wizard at not possible
start up
System does System does
not start not function
(white LED is
off)
Frequency:
every X months
X=3
X
X
X
X
X
possible Solution
cause
Refer to HMI; Refer to HMI
for more info,
refer to the
online user
manual
Panel is in Put the rotary
service mode switch on the Panel
to 0 (refer to Fig.
6.1H)
Loose Tighten the HMI
connection cable to the CAN
connector (refer to
Fig. 4.7B+C)
Loose or Connect the HMI
incorrectly cable to the CAN
connected cable HMI connector
(refer to Fig. 4.10)
System Direct to screen 5.8
configured in to restart the
an earlier stage wizard manually
If necessary: reset
PIN (refer to online
user manual)
No mains Connect the mains
voltage voltages
Main switch is Turn the main
off switch to on (refer
to Fig. 6.1E)
X=12
X
EN - 16