General Safety Instructions; Special Safety Information; Overview Of The Components; Instruction Manual - AEG SRR 4311 Instrucciones De Servicio

General Safety Instructions

Read the operating instructions carefully before putting the appli-
ance into operation and keep the instructions including the warran-
ty, the receipt and, if possible, the box with the internal packing.
• To avoid the risk of fi re or an electric shock, you should not
expose the device to rain or moisture. Consequently, do not
use the device in the immediate vicinity of water - for examp-
le near a bath tub, a swimming pool or in a damp cellar.
• Use the device only for the intended purpose.
• Only connect the device at a properly installed plug socket.
Pay attention that the specifi ed voltage corresponds to the
voltage of the plug socket.
• When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries in
the correct direction.
• Assemble the device in such a way that the available
ventilation openings are not covered.
• Never open the housing of the device. Incorrect repairs can
constitute a considerable risk for the user. Should the device
become damaged, in particular the mains supply cable, do
not operate the device any longer, but rather have it repaired
by an expert. Check the mains supply cable regularly for
damage.
• For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manufactu-
rer, our customer service department or a similary qualifi ed
person.
• If the device is not used for a longer period, remove the plug
connector from the plug socket or take out the batteries.
These symbols may be found on the machine and are intended
to indicate the following:
The lightning symbol should advise the user of parts
in the inside of the device which carry dangerously
high voltage levels.
The symbol with an exclamation mark should advise
the user of important operation or maintenance
instructions in the accompanying documentation.
Devices bearing this symbol work with a „class 1
laser" for tracing the CD. The built-in safety switches
should prevent the user being exposed to dange-
rous laser light, which is invisible to the human eye,
when the CD compartment is opened.
Under no circumstances should these safety switches be
bypassed or manipulated, as this could result in a danger of
exposure to the laser light.
Children
• In order to ensure your children's safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
Caution! Do not allow small children to play with the foil as
there is a danger of suffocation!
• To protect children from the dangers posed by electrical
appliances, make sure that the cable is hanging low and that
children do not have access to the appliance.
05-SRR 4311 AEG 39

Special safety information

This device works with
a class 1 laser.

Overview of the Components

1 POWER control lamp
2 FM ST. control lamp
3 Handle
4 Loudspeaker
5 VOLUME + / - (volume control)
6 Function selector switch (RADIO / TAPE / CD/USB/CARD)
7 USB connection
8 TUNING control
9 PROG. button (memory)
10 MODE button (repeat/random)
11 CD compartment
12 PUSH/OPEN CD compartment
13 LCD display
14 II / USB button (Play/Pause / USB CD switching)
15 I / DIR+ button (forward search / album upwards)
16 I / DIR- button (reverse search / album downwards)
17 / CARD button (Stop /USB CARD switching)
18 Band selector switch (AM / FM / FM ST.)
19 Cassette compartment
20 II Pause button - cassette
21 / Stop/Eject button - cassette
22 Forward button - cassette
23 Reverse button - cassette
24 Playback button - cassette
25 b Playback button - cassette
26 SD/MMC Card Slot
27 Station scale
Reverse Side
28 Battery compartment
29 AC~ IN Mains connection
30 VHF /FM aerial
31 BEAT CUT A/B switch
32 Headphone connection
33 MIC (Microphone) socket
Start-up of the device/introduction
• Read the operating instructions thoroughly before the start-
up!
• Select an appropriate location for the device, e.g. a dry, fl at,
non-slip surface on which the device can be easily operated.
• Make sure that the device is adequately ventilated!
• Connect the power cable supplied (see battery compart-
ment (28) if necessary) to a properly installed 230 V/50 Hz
safety power socket and the mains connector AC~ IN (29)
on the back of the machine. Ensure that the voltage is the
same as that indicated on the model identifi cation plate.
• The POWER (1) control lamp shows the function.
39
21.04.2006, 9:37:45 Uhr