Symbols Used In This Manual; For Your Safety; Symbols On The Power Tool; Intended Use - Flex LE 9-11 125 Instrucciones De Funcionamiento Originales

L 9-11 125/LE 9-11 125/L 12-11 125/L 15-11 125/LE 15-11 125/L 1400 125

Symbols used in this manual

WARNING!
Denotes impending danger. Non-observance of this warning
may result in death or extremely severe injuries.
CAUTION!
Denotes a possibly dangerous situation. Non-observance of
this warning may result in slight injury or damage to property.
NOTE
Denotes application tips and important information.

Symbols on the power tool

Before switching on the power tool, read the
operating manual!
Wear goggles!
Protection class II (completely insulated)
Disposal information for the old machine
(see page 14)
Prevents kickback of the machine if the tool
becomes blocked. (On angle grinders with
variable speed only from speed setting 4 to 6)
Overload protection: switches the machine off
in the event of overload.
A tachogenerator prevents the speed from fal-
ling under load.
Better work safety and improved handling
thanks to gentle speed development.
Sensor-controlled temperature monitoring: If
there is a risk of overheating the machine swit-
ches off.
Prevents unintentional machine start after
a power failure.
The speed can be set variably in 6 stages.

For your safety

WARNING!
Before using the angle grinder, please read and follow:
–
these operating instructions,
–
the "General safety instructions" on the handling of power
tools in the enclosed booklet (leaflet-no.: 315.915),
–
the currently valid site rules and the regulations for the
prevention of accidents.
This angle grinder is state of the art and has been constructed
in accordance with the acknowledged safety regulations.
Nevertheless, when in use, the power tool may be a danger to
life and limb of the user or a third party, or the power tool or
other property may be damaged.
The angle grinder may be operated only if it is
–
as intended,
–
in perfect working order.
Faults which impair safety must be repaired immediately.

Intended use

This angle grinder
–
for commercial use in industry and trade,
–
is designed for dry grinding and cutting metal and stone;
a special cutting guard must be used for cutting,
–
for use with grinding tools and accessories which are
indicated in these instructions or recommended by the
manufacturer.
Not permitted are e.g. chain cutting wheels, saw blades and
(L 9-11 125, LE 9-11 125, L 12-11 125 only) diamond grinding
disc.

Safety Warnings for Angle Grinder

WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference.
Safety Warnings Common for Grinding or Abrasive
Cutting-Off Operations
This power tool is intended to function as a grinder or

cut-off tool. Read all safety warnings, instructions, illu-
strations and specifications provided with this power
tool. Failure to follow all instructions listed below may re-
sult in electric shock, fire and/or serious injury.
Operations such as sanding, wire brushing or polis-

hing are not recommended to be performed with this
Operations for which the power tool was
power tool.
not designed may create a hazard and cause
personal injury.
Do not use accessories which are not specifically de-

signed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
The rated speed of the accessory must be at least

equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fly apart.
The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of con-
trol.
11