Maintenance And Care; Disposal Information - Flex LE 9-11 125 Instrucciones De Funcionamiento Originales

Switch on the angle grinder with the switch (without engag-

ing it) and run the angle grinder for approx. 30 seconds.
Check for imbalances and vibrations.
Switch off the angle grinder.

Switching on and off
Brief operation without engaged switch rocker
(Figure H)
Push the switch rocker forwards and hold in position.

To switch off the power tool, release the switch rocker.

Continuous operation with engaged switch rocker
Figure I:
Push the switch rocker forwards (1.) and engage by pres-

sing the front end (2.).
Figure J:
To switch off the power tool, release the switch rocker by

pressing the rear end.
NOTE
Following a power failure, the switched on power tool does not
restart.
Preselecting the speed (LE 9-11 125,
LE 15-11 125) (Figure K)
To set the operating speed, move the dial to the required

value.
CAUTION!
Risk of injury due to destruction of the tool. Use the appropriate
tool for the job.
NOTE
If an overload or overheating occurs during continues opera-
tion, the power tool automatically reduces the speed until the
power tool has cooled down adequately
(L 12-11 125, L 15-11 125, LE 15-11 125).
Adjusting the guard (Figure L)
To adjust the tool to the task at hand, the guard hood can be
adjusted by 12 notches on 360° without a tool.
CAUTION!
Risk of injury! Wear protective gloves.
Pull out the mains plug.

Turn guard hood opposite to the direction-of-rotation arrow

on the gear head to the required position.
Work instructions
NOTE
When the power tool is switched off, the grinding tool continues
running briefly.
Rough-grinding
WARNING!
Never use cutting-off wheels for rough-grinding.
–
Angle of wheel 20–40° for best cutting performance.
–
Applying moderate pressure, move the angle grinder
backwards and forwards. As a result, the workpiece will not
become too hot and there will be no discoloration; nor will
there be any grooves.
14
L 9-11 125/LE 9-11 125/L 12-11 125/L 15-11 125/LE 15-11 125/L 1400 125
Cut-off grinding (Figure M)
WARNING!
A special cutting guard must be used for cutting.
See manufacturer's accessories catalogue.
–
Do not press, tilt or oscillate the power tool.
Otherwise, there is a risk of the angle grinder jumping
uncontrollably out of the groove.
–
The angle grinder must always be operated backwards.
–
Adjust the feed to the material which is to be cut: the harder
the material, the slower the feed.
For further information on the manufacturer's products go to
www.flex-tools.com.

Maintenance and care

WARNING!
Before carrying out any work on the angle grinder, always pull
out the mains plug.
Cleaning
WARNING!
If metals are ground or cut over a prolonged period, conductive
dust may become deposited inside the housing. Impairment of
the protective insulation! Operate the power tool via a residual-
current-operated circuit-breaker (tripping current 30 mA).
Regularly clean the power tool and ventilation slots. Fre-

quency of cleaning is dependent on the material and dura-
tion of use.
Regularly blow out the housing interior and motor with dry

compressed air.
Carbon brushes
The angle grinder features cut-off carbon brushes.
When the wear limit of the cut-off carbon brushes is reached,
the angle grinder switches off automatically.
NOTE
Use only original parts supplied by the manufacturer for replacement
purposes. If non-original parts are used, the guarantee obligations of
the manufacturer will be deemed null and void.
Gears
NOTE
Do not loosen the screws on the gear head during the warranty
period. Non-compliance will deem the guarantee obligations of
the manufacturer null and void.
Repairs
Repairs may be carried out by an authorised customer service
centre only.
Spare parts and accessories
For other accessories, in particular grinding tools, see the ma-
nufacturer's catalogues.
Exploded drawings and spare-part lists can be found on our ho-
mepage: www.flex-tools.com

Disposal information

WARNING!
Render redundant power tools unusable by removing the po-
wer cord.