Service Information - Black+Decker JS10 Manual De Instrucciones

20 • ENGLISH
possible to the clamping point to eliminate any vibration
of the work being cut.
When cutting conduit, pipe or angle iron, clamp work
in a vise if possible and saw close to the vise. To cut
thin sheet materials, "sandwich" the material between
hardboard or plywood and clamp the layers to eliminate
material vibration and tearing. By doing this, the material
will be cut smoothly. Lay out your pattern or cutting lines
on top of the "sandwich".
MAINTENANCE
General
Warning! Do not at any time allow solvents such
as brake fluids, gasoline, petroleum-based products,
penetrating oils, etc. to come in contact with plastic parts.
They contain chemicals that can damage, weaken or
destroy plastic. Use a clean dry cloth to remove dirt, dust,
oil, grease, etc.
Warning! Use safety goggles when using an air jet to
blow dust out of the jigsaw. Using this jigsaw for cutting
fiberglass, wallboard or plaster will result in accelerated
wear due to the abrasive nature of these materials. It is
important that you clean the jigsaw frequently when cutting
these materials.
DO NOT abuse power tools. Abusive practices can damage
the tool as well as the workpiece.
Warning! DO NOT attempt to modify this jigsaw or
create accessories not recommended for this jigsaw. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious injury.
It will also void the warranty.
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
f Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
f Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
LUBRICATION
All of the bearings in this jigsaw are lubricated with a
sufficient amount of high- grade lubricant for the life of
the unit under normal conditions. Therefore, no further
lubrication is required.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste. Should
you find one day that your BLACK+DECKER
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials. Local regulations may
provide for separate collection of electrical products
from the household, at municipal waste sites or
by the retailer when you purchase a new product.

SERVICE INFORMATION

BLACK+DECKER offers a full network of company-owned
and authorized service locations. All BLACK+DECKER
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service. For more information about our authorized service
centers and if you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest you, or visit us at
www.BlackandDecker-la.com
SPECIFICATIONS
Power
Blade speed
Stroke length
Cutting depth @ 90°
Steel
Wood
Sole plate tilt
SPECIFICATIONS
Power
Blade speed
Stroke length
Cutting depth @ 90°
Steel
Wood
Sole plate tilt
JS10
400W
3000/min (spm)
no load
11/16"
15/64" (6 mm)
2-9/16"(65mm)
0–45°
JS20
400W
1000-3000/min (spm)
no load
11/16"
15/64" (6 mm)
2-9/16"(65mm)
0–45°