Functional Description - Makita DPO500 Manual De Instrucciones

Tips for maintaining maximum
battery life
1 . Charge the battery cartridge before completely dis-
charged. Alw ays stop tool operation and charge the
battery cartridge w hen you notice less tool pow er.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge w ith room tempera-
ture at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let a hot
battery cartridge cool do w n before charging it.
4 . Charge the battery cartridge if you do not use
it for a long period (more than six months).
FUNCTIONAL
DESCRIPTION
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Al w ays s w itch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.1: 1. R e d in d i c ator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.2: 1. I n d i c ator lamps 2. C h e c k button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
lig h t up f or a f e w se c on d s.
Indicator lamps
Lighted
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
pla c e d un d er one o f t h e f ollo w ing c on d itions :
Overload protection
When the tool or battery is operated in a manner that
causes it to draw an abnormally high current, the tool
automatically stops without any indication. In this sit-
uation, turn t h e tool o f f an d stop t h e appli c ation t h at
c ause d t h e tool to be c ome o v erloa d e d . T h en turn t h e
tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically. In this case, let the tool and battery cool
be f ore turning t h e tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
7 ENGLISH
Off Blinking
75 %
mal f un c tione d .
Remaining
capacity
to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
C h arge th e
battery.
The battery
may have