Makita DVC265 Manual De Instrucciones página 14

Connecting the tool
I f t h e bent pipe assembl y is atta c h e d to t h e h ose,
loosen t h e slee v e o f bent pipe assembl y an d remo v e it.
Fig.12: 1. H ose 2. Bent pipe assembl y 3. S lee v e
1. A tta c h t h e f ront c u f f to t h e h ose f or d ust e x tra c tion.
W h en c onne c ting t h e f ront c u f f , make sure t h at it is
se c urel y s c re w e d on t h e h ose.
2. C onne c t t h e f ront c u f f to t h e tool ' s e x tra c tion
outlet.
Fig.13: 1. F ront c u f f 2. E x tra c tion outlet 3. H ose
T h e f ront c u f f c an be d eta c h e d b y turning it c ounter-
c lo c k w ise w h ile h ol d ing t h e h ose.
NOTE: A l w a y s use a suitable f ront c u f f . W h en using
t h e f ront c u f f 2 4 , atta c h it to t h e f ront c u f f 22 t h at is
c onne c te d to t h e h ose.
Fig.14: 1. F ront c u f f 22 2. F ront c u f f 2 4
Using as a cleaner
I f y ou w ant to use t h is pro d u c t as a c leaner, f ollo w t h e
belo w pro c e d ures.
NOTICE:
If the front cuff is attached to the hose,
remove it beforehand.
NOTE: T h e bent pipe assembl y , e x tension w an d , an d
no z z les are supplie d as optional a c c essories in some
c ountries.
NOTE: T h ere are t w o t y pes o f bent pipe assembl y ;
t h e one f or sli d e-t y pe e x tension w an d an d t h e one f or
ring-t y pe e x tension w an d . I f y ou prepare t h e bent pipe
assembl y , c h oose t h e one f or y our d esire d e x tension
w an d t y pe.
1. F asten t h e slee v e o f bent pipe assembl y onto t h e
h ose.
Fig.15: 1. H ose 2. Bent pipe assembl y 3. S lee v e
T o remo v e t h e bent pipe assembl y , loosen t h e slee v e o f
bent pipe assembl y f rom t h e h ose.
2. T w ist an d insert t h e no z z le to t h e e x tension w an d .
Fig.16: 1. E x tension w an d 2. F ree no z z le
3. T -s h ape no z z le 4. T -s h ape no z z le ( slim )
NOTE: B y t w isting t h e no z z le w h ile inserting, t h e no z -
z le c an be atta c h e d to t h e e x tension w an d se c urel y .
3. F ollo w t h e pro c e d ures belo w , d epen d ing on t h e
t y pe o f t h e e x tension w an d :
NOTE: T h e sli d e-t y pe e x tension w an d an d t h e ring-
t y pe e x tension w an d are not c ompatible w it h ea c h
ot h er. I f y ou w ant to c h ange t h e sli d e-t y pe e x tension
w an d to t h e ring-t y pe e x tension w an d or v i c e v ersa,
c h ange t h e bent pipe assembl y also.
NOTE: T h e f ree no z z le c an be atta c h e d to t h e bent
pipe assembl y d ire c tl y .
For the slide-type extension wand
S h oul d er t h e v a c uum c leaner bo d y t h en insert t h e
e x tension w an d into t h e bent pipe assembl y until it
c li c ks. T o d is c onne c t, e x tra c t t h e e x tension w an d w it h
pressing t h e button.
Fig.17: 1. Bent pipe assembl y 2. Button 3. S li d e-
t y pe e x tension w an d 4. F ree no z z le
The length of the wand can be adjusted.
With pressing the slide button, adjust the wand length.
T h e lengt h is lo c ke d w h en release t h e sli d e button.
Fig.1 8 : 1. S li d e button
For the ring-type extension wand
S h oul d er t h e v a c uum c leaner bo d y t h en t w ist an d insert
t h e e x tension w an d into t h e bent pipe assembl y . T o
d is c onne c t, t w ist an d e x tra c t it.
Fig.19: 1. Bent pipe assembl y 2. R ing-t y pe e x ten-
sion w an d 3. F ree no z z le
The length of the wand can be adjusted.
Loosen the ring on the wand and adjust the wand
lengt h . T ig h ten t h e ring at y our d esire d lengt h .
Fig.20: 1. R ing
Hose hook
W h en y ou suspen d t h e operation, t h e h ook on t h e bent
pipe assembl y c an be use d f or h anging t h e w an d on t h e
lo w er belt.
Fig.21
Installing filter bag / dust bag
Optional accessory
Do not use a damaged filter bag.
CAUTION:
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust
or particles may be exhausted from the cleaner
and they may cause respiratory disease to the
operator.
When the filter bag is already full, replace
NOTICE:
w it h ne w one. W h en t h e d ust bag is alrea d y f ull,
empty it. Continuous use with the filter bag/dust bag
f ull results in re d u c e d su c tion po w er.
1. U nlo c k t h e lat c h b y li f ting t h e bottom si d e. P us h
t h e groo v e d area to li f t t h e f ront lat c h ing si d e. P ull t h e
lat c h to open t h e li d .
Fig.22: 1. H ook 2. L i d
Insert the filter bag into the slit on the upper side of
2.
t h e room as illustrate d .
Fig.23: 1. S lit 2. F ilter bag
W h en using t h e d ust bag, insert t h e brim o f t h e d ust bag
into t h e slit.
Fig.24: 1. S lit 2. Brim 3. D ust bag
Align the hole of the filter bag with the hose cuff
3.
an d pus h t h e c ar d boar d portion to t h e en d . Make sure
that the rubber ring on the filter bag goes over the rim
on t h e h ose c u f f .
Fig.25: 1. Rubber ring on the filter bag 2. R im on
t h e h ose c u f f 3. C ar d boar d portion o f t h e
filter bag 4. H ose c u f f
14 ENGLISH