Electrical Wiring - Mitsubishi Electric CITY MULTI PAC-PH01EHYU-E Manual De Instalación

[Fig. 7.0.3]
<A> Attach the rubber spacer to the screw hole.
<B> Attach the panel heater to the upper side of the rear
panel and tighten it with two screws together.
(Attach the panel heater using the supplied long type
M5 screws.)
A Rear panel
B Rubber spacer
C Panel heater B
(Left wiring port type, wiring color: White)
<PAC-PH02EHYU-E>, <PAC-PH03EHYU-E>
• Panel heater installation
[Fig. 7.0.1]
<A> Attach the panel heater to the upper side of the left
panel and tighten it with two screws together.
A Left panel
B Panel heater L
(Left wiring port type, wiring color: Yellow)

8. Electrical Wiring

<PAC-PH01EHYU-E>
• Wiring on the left side and installing the wiring cover
[Fig. 8.1.0.1]
<A> Cut the tie band that fixes the cover of the unit wiring
and remove the cover.
<B> Remove the water-proof cap from the unit wiring
connector (the male end of the connecter).
<C> Pull up the panel heater wirings so that the wirings run
along the left rear pillar.
<D> Connect the panel heater wiring and the unit wiring and
run the connected wiring between the fin guard and the
pillar.
<E> Place the cover back and fix the cover with the tie band.
A Unit wiring
B Cover
C Tie band
D Water-proof cap on the unit wiring connector
E Panel heater wiring
F Fin guard
G Pillar
[Fig. 8.1.0.2]
<A> Screw down the metal sheet wiring cover and the fin
guard at three points.
A Fin guard
B Cover wiring 1
C Cover wiring 4
D Cover wiring 2
• Wiring on the right side and installing the wiring cover
[Fig. 8.1.0.3]
<A> As with <A> and <B> in [Fig.8.1.0.1], remove the water-
proof cap from the unit wiring connector.
<B> Pull up the panel heater wirings so that the wirings run
along the right rear pillar.
<C> Connect the panel heater wiring and the unit wiring and
run the connected wiring between the fin guard and the
pillar.
<D>As with <E> in [Fig.8.1.0.1], place the cover back and fix
the cover with the tie band.
A Unit wiring
B Cover
C Panel heater wiring
28
[Fig. 7.0.2]
<A> Attach the panel heater to the upper side of the right
panel and tighten it with two screws together.
A Right panel
B Panel heater R
(Right wiring port type, wiring color: Blue)
[Fig. 7.1.1]
<A> Attach the rubber spacer to the screw hole.
<B> Attach the panel heater to the upper side of the rear
panel and tighten it with two screws together.
(Attach the panel heater using the supplied long type
M5 screws.)
A Rear panel
B Rubber spacer
C Panel heater BR
(Left wiring port type, wiring color: White)
D Panel heater BL
(Right wiring port type, wiring color: Red)
D Fin guard
E Pillar
F Tie band
[Fig. 8.1.0.4]
<A> Screw down the metal sheet wiring cover and the fin
guard at three points.
A Fin guard
B Cover wiring 1
C Cover wiring 3
• Wiring on the rear side and installing the wiring cover
[Fig. 8.1.0.5]
<A> As with <A> and <B> in [Fig.8.1.0.1], remove the water-
proof cap from the unit wiring connector.
<B> Pull up the panel heater wirings so that the wirings run
along the right rear pillar.
<C> Connect the panel heater wiring and the unit wiring and
run the connected wiring between the fin guard and the
pillar.
<D> As with <E> in [Fig.8.1.0.1], place the cover back and
fix the cover with the tie band.
A Unit wiring
B Cover
C Panel heater wiring
D Fin guard
E Pillar
F Tie band
[Fig. 8.1.0.6]
<A> Screw down the metal sheet wiring cover and the fin
guard at three points.
A Fin guard
B Cover wiring 1
C Cover wiring 2