Campbell Hausfeld WG3080 Manual De Instrucciones De Operación Y Lista De Partes página 12

Operating Instructions and Parts Manual
For Information About This Product Call 1-800-746-5641
Symptom
No output
Wire tangles at drive roller
Gun nozzle arcs to work surface
Work clamp and/or cable gets hot
Wire does not feed
(Aluminum) Wire burns back into
tip or (Aluminum) Metal bubbles or
burns through
Weld pops and sputters
Bead is intermittently too thin
Bead is intermittently too thick
Ragged depressions at edge of
weld
Weld bead does not penetrate base
metal
Wire sputters and sticks
12
Troubleshooting Chart - Welder
Possible Cause(s)
1. Duty cycle exceeded
2. Poor work clamp connection
3. Tripped circuit breaker
4. Blown breaker or fuse
1. Wrong size contact tip
2. Torch liner clogged or damaged
3. Contact tip clogged or damaged
4. Drive roller worn
5. Not enough tension
1. Slag inside gun nozzle
2. Insulation ring melted/expired
1. Poor contact
2. Using an extension cord with
excessive length
1. Wire jammed
2. Out of wire
3. Not enough tension
4. Wire liner worn
5. Wire disconnected internally
6. Contact tip clogged
1. Wire speed too slow
2. Travel speed too slow or heat is
too high
1. Wire speed setting
2. Contact tip size too large
3. Polarity set incorrectly
4. Drive roller slipping
5. Gas bottle empty
1. Inconsistent travel speed
2. Output heat setting too low
1. Slow and/or inconsistent travel
speed
2. Output heat setting too high
1. Travel speed too fast
2. Wire speed too fast
3. Output heat setting too high
1. Inconsistent travel speed
2. Output heat setting too low
3. No or low shielding gas
4. Wrong shielding gas (aluminum)
5. Extension cord is too long
6. (Aluminum) Possible oxide buid-
up on surface
1. Damp wire
2. Wire speed too fast
3. Wrong type of wire
4. No or low shielding gas
www.campbellhausfeld.com
Corrective Action
1. Allow welder to cool until lamp goes out
2. Be sure all connections are secure, and attaching
surface is clean
3. Reset by pushing button on back of unit
4. Reduce circuit load, reset breaker or replace fuse
1. Use proper size contact tip
2. Clean or replace wire liner
3. Clean or replace contact tip
4. Replace
5. Tighten tension knob
1. Clean slag from gun nozzle
2. Replace nozzle
1. Be sure all connections are secure, and attaching
surface is clean
2. Never use an extension cord longer than 20 ft
1. Reload wire
2. Replace wire spool
3. Tighten tension knob if wire is slipping
4. Replace liner
5. Call 1-800-746-5641 for assistance
6. Replace contact tip
1. Run speed in 7 - 10 range
2. Increase the travel speed or reduce heat settings
1. Tune in correct setting (1-5 mild steel; 5-10
aluminum)
2. Replace contact tip
3. Reverse polarity
4. Increase tension
5. Replace gas bottle
1. Decrease and maintain constant travel speed
2. Increase output heat setting
1. Increase and maintain travel speed
2. Reduce output heat setting
1. Decrease travel speed
2. Decrease wire speed
3. Reduce output heat setting
1. Decrease and maintain constant travel speed
2. Increase output heat setting
3. Use gas for MIG process or refill bottle
4. Use only 100% Argon gas
5. Never use an extension cord longer than 20 ft
6. Clean surface thoroughly with a stainless steel
brush only
1. Use dry wire and store in dry location
2. Reduce wire speed
3. Use flux-cored wire when not using gas
4. Use gas for MIG process or refill bottle