Westin 22-1785 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
TROUSSE DE MONTAGE
22-1785
CHROME/ CROMADO /CHROME
22-0060, 22-5060
BLACK/NEGRO/NOIR
22-0065, 22-5065
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2)
3,4 2 FRONT BRACKET, PASSENGER (3) AND DRIVER (4)
5,6 2 REAR BRACKET, PASSENGER (5) AND DRIVER (6)
7 2 MOUNT BRACE
8,9 2 MOUNT PLATE, PASSENGER (8) AND DRIVER (9)
10 10 3/8-16 X 1.25" HEX HEAD BOLT
11 14 3/8" FLAT WASHER
12 12 3/8" LOCK WASHER
13 4 3/8-16 HEX NUT
14 8 1/4-20 X .75 T-HEAD BOLT
15 8 1/4" FLAT WASHER
16 8 1/4-20 NYLON INSERT LOCK NUT
17 2 BOLT PLATE
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) Y CONDUCTOR (2)
3,4 2 SOPORTES DELANTERAS, ACOMPAÑANTE (3) Y CONDUCTOR (4)
5,6 2 SOPORTES TRASERAS, ACOMPAÑANTE (5) Y CONDUCTOR (6)
7 2 PIEZA DE SUJECIÓN DEL SOPORTE
8,9 2 PLACA DE MONTAJE, ACOMPAÑANTE (8) Y CONDUCTOR (9)
10 10 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
11 14 ARANDELAS PLANAS DE 3/8"
12 12 ARANDELAS DE PRESIÓN DE 3/8"
13 4 TUERCAS HEXAGONALES DE 3/8-16
14 8 PERNOS CON CABEZA EN T DE 1/4-20 X .75"
15 8 ARANDELAS PLANAS DE 1/4"
16 8 TUERCA DE FIJACIÓN HEXAGONAL 1/4-20
17 2 BASE DE MONTAJE
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2)
3,4 2 SUPPORTS AVANT, PASSAGER (3) ET CONDUCTEUR (4)
5,6 2 SUPPORTS ARRIERE, PASSAGER (5) ET CONDUCTEUR (6)
7 2 RENFORTS POUR SUPPORTS
8,9 2 PLAQUE DE MONTAGE, PASSAGER (8) ET CONDUCTEUR (9)
10 10 BOULON A TETE HEXAGONALE DE 3/8-16 X 1,25 PO
11 14 RONDELLE PLATE DE 3/8 PO
12 12 RONDELLE A FREIM DE 3/8 PO
13 4 ÉCROUS HEXAGONAUX 3/8-16
14 8 BOULONS A TETE-T 1/4-20 X .75 PO
15 8 RONDELLES PLATES 1/4 PO
16 8 1/4-20 ÉCROU DE BLOCAGE SIX PANS
17 2 PLAQUES DE BOULON
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
STEP 2.
Determine passenger and driver brackets.
STEP 3.
Locate rear mount holes (one slot and one hole) on underside of the rocker panel below passenger rear door. Insert
mount plate into slot so holes of mount plate line up with mount holes on vehicle. High side of mount plate should face
SEE FIGURE 1.
up.
STEP 4.
Attach rear bracket to vehicle rocker panel using 3/8" fasteners as shown. Hand tighten.
STEP 5.
Locate front mount holes (one slot and one hole) on bottom of unibody rail below front door. Insert mount plate into slot
so holes of mount plate line up with mount holes on vehicle. High side of mount plate should face up.
STEP 6.
Attach front bracket to vehicle rocker panel using 3/8" fasteners as shown. Hand tighten.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2008 FORD ESCAPE/MAZDA TRIBUTE/MERCURY MARINER
APLICACIÓN: FORD ESCAPE/MAZDA TRIBUTE
APPLICATION: FORD ESCAPE/MAZDA TRIBUTE/MERCURY MARINER 2008
2
CONTENTS - CONTENIDO
3
1
4
- CONTENU
WO:
/MERCURY MARINER , MOD. 2008
7
5
8
6
TOOLS - HERRAMIENTA
9/16" SOCKET
7/16" SOCKET
9/16" WRENCH
RATCHET
TORQUE WRENCH
DADO DE 9/16"
DADO DE 7/16"
LLAVE DE TUERCAS DE 9/16"
MANERAL
LLAVE DE TORQUE
DOUILLE 9/16 PO
DOUILLE 7/16 PO
CLE 9/16 PO
CLIQUET
CLEF DE COUPLE
SEE FIGURE 1.
SEE FIGURE 1.
SEE FIGURE 1.
75-0836 REVISION 7/9/07
9
17
- OUTILS