Cadet Energy Plus CE163T Manual Del Usuario página 6

WARNING Risk of Electrical Shock and Fire.
The heater must be properly installed before it is used.
1. Do not operate without grill.
2. Keep electrical cords, drapery, furnishings and other com-
bustibles at least 3 feet (0.9 m) away from the front of the
heater and 6 inches (15.2 cm) away from the sides.
3. Do not tamper with the over temperature limit control.
4. If the heater over temperature limit trips more than once
per day, the heater must be replaced.
5. Clean heater at least every six months.
Digital Display and Control Buttons
Fan
Operation
Indicator
73
Temperature
Night /
Away
Heating
Mode
HEATER MODES
Use the mode button to alternate between HEAT (display
shows room temperature), STOP HEATING/NO FAN (display
shows 0), and FAN ONLY (display shows 1, 2 or 3).
HEAT MODE
Your Energy Plus heater has a unique variable speed blower
that auto adjusts heat output based on the room's requirements.
Once you set your desired temperature, the heater will vary the
wattage output for maximum efficiency.
The digital display will show the level of heat being output to
maintain the room's temperature.
68
Heating Full Power Heating Mid Power Heating Low Power
START HEATING/SET TEMPERATURE
68
• Press mode button. Display shows room temperature.
• Press the up or down
temperature.
Temperature Setpoint Range: 40˚F - 86˚F (4.4˚C - 30˚C)
STOP HEATING/NO FAN
Press mode button until display
shows '0'.
NOTE: Fan will run until heater cools
down. This phase could last for five
minutes or more.
Page 6
OPERATING INSTRUCTIONS
Night/Away
Mode Indicator
Heating Output
Indicator
Up
Down
68 68
68 68
button to set your desired
NO
0
Stop Heating / No Fan
NO
0
6. After allowing the heater to cool, turn power off at circuit
breaker panel before removing grill.
7. Use a hair dryer or vacuum on blow cycle to blow debris
through the top element (do not touch element).
8. Install the grill before turning on power.
WARNING: Any other service not detailed in this Own-
er's Guide should be performed by an authorized service
representative.
FAN ONLY MODE
The FAN ONLY mode can circulate air
but will not supply heat.
Press until display shows '0'. Push
to choose 1 for low speed, 2 for medium
speed, or 3 for high speed.
PROGRAMMING NIGHT/AWAY SET POINT
Preset a night or away temperature set point, for quick and easy
"one-touch" energy savings.
• Press mode button until display shows room temperature.
• Press night button. The moon icon will show in display
screen. The "night/away" set point temperature will briefly
flash.
• Press up or down to adjust night/away set point.
• To exit the night/away mode
when you awake or return, press the
night again. The moon icon
will no longer be in display screen.
• To return to your previous night/away
set point, simply press the night
MAX/MIN TEMPERATURE LOCK
Preset a maximum and/or minimum set point as a child safety
or tamperproof option. To preset a maximum setpoint:
• Press mode button until display shows '0'.
• Press and hold both night
same time, for at least 5 seconds, until the 'HL' (high limit)
temperature is displayed.
• Release buttons: temperature setpoint will alternate with 'HL'
on the display.
• Using the up or down
• To preset a minimum setpoint, press mode
flash, set low temperature setting.
• Wait a minimum of 15 seconds for display to return to '0', and
your settings will be saved.
• To remove the lock, follow same instructions, and set to
maximum of 86˚F (30˚C), or minimum of 40˚F (4.4˚C).
• Press to return to HEAT mode.
CHANGE DISPLAY TO CELSIUS
• Press mode button until display shows '0'.
• Press and hold both night
same time, for at least 5 seconds, until the 'HL' (high limit)
temperature is displayed.
twice, until display alternates between o F and
• Press mode
U .
• Press to convert to Celsius.
• Wait a minimum of 15 seconds until display stops flashing.
• Press to return to HEAT mode.
3 3
Fan Only / High Speed
3 3
NO
55
NO
55
button.
Night/Away Mode
NO
55
NO
55
and down buttons at the
button, set maximum set point.
button, 'LL' will
and down buttons at the