Operating Thetransmitter - Audio-Technica 1800 Serie Instalación Y Manejo

OM1800Ser_dual(europ).qxd:Layout 1
12
E
POWER
MUTE
SET
N
Turning your Transmitter On & Off
How to Set Frequencies
How to Access & Use the Function Menu
1/10/07 14:35 Page 12
Transmitter Batteries
Battery Selection
Each transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended.
Always replace both batteries. Make certain the transmitter power is Off before replacing batteries.
Transmitter Battery
1. Open the battery compartment door by sliding the catch down (on body-pack) or pushing in
Installation direction of arrow (on plug-on transmitter).
2. Observe correct polarity as marked on the metal contacts on the door and carefully insert
two fresh 1.5V AA alkaline batteries.
3. Close the door, making certain the latch clicks securely in place.
Battery Condition
After the batteries are installed, turn the power on by pressing and holding the Power/Mute
button. The small power-on LED ( see (
a
come on. If this does not happen, the batteries are installed incorrectly or they are depleted.
The transmitter's "fuel gauge" battery indicator in the LCD displays a maximum of four bar
segments. When it flashes "LOW.BAT" , the batteries should be replaced immediately to ensure
continued operation. (Additionally, the power-on LED will flash when the batteries are low.)

Operating theTransmitter

To turn the transmitter on, press and hold the Power/Mute button until the power indicator lights
green, and the LCD window comes on (about 1-2 seconds). The operating frequency will show in
the window after the power-up sequence.
To turn the transmitter off, press and hold the Power/Mute button again, until the power indicator
and the LCD window are extinguished (about 1-2 seconds). The LCD window will show
"PWR.OFF" before shutdown.
NOTE: Transmitter-Receiver pairs must be set to identical frequencies: set Transmitter 1
on your Transmitter
to the same frequency as Receiver Channel 1; set Transmitter 2 to the same frequency as
Receiver Channel 2.
1. Turn transmitter on.
2. Press the Set button once and the small word "MENU" will appear above the frequency.
3. Press the Set button again and the small flashing word "EDIT" will appear to the right
of "MENU" .
4. Use the Up/Down arrows to change the transmitter frequency. Press either arrow for 25 kHz
steps, or hold down either arrow for rapid cycling through the range. Frequencies "wrap
around" when the top or bottom of the band is reached. Select the exact frequency
displayed on the receiver.
5. To activate this frequency selection, press and hold the Set button until the word "STORED"
appears in the transmitter's window. (If you do not wish to complete this selection, just
press the Set button once: the word "ESCAPE" will appear briefly in the window and the
transmitter will return to the Menu mode.)
6. When finished entering a frequency, press the Up arrow once to move to "QUIT". Then press
the Set button once to exit the menu. The word "MENU" in the transmitter window will
go off, indicating the return to normal operation.
1. Turn transmitter on.
on your Transmitter 2. Press the Set button once; the small word "MENU" will appear above the frequency.
3. When in the Menu mode, use the Up and Down arrows to cycle through the following functions:
• Frequency
• RF Power
• Audio Input Level
• Power/Mute Locks
4. To make a change in the default setting:
• Press Set button once;
• Press Up or Down arrow until you reach desired setting;
• Press and hold Set button until the word "STORED" appears in the LCD window.
• (If you do not wish to complete this selection, just press the Set button once: the word
"ESCAPE" will appear briefly in the window and the transmitter will return to the Menu mode.)
ATW-T1801
a ) at left ) should light green and the LCD window should
• Input Select (body-pack only)
• Reset to Defaults
• Quit (exit menu)
ATW-T1802