Error Message - SMA LIGHT 360 Manual De Usuario

Minimal Skin Discomfort
Despite the domestic pulsed light treatments are generally tolerated very well, most users try a
annoyance during use, generally described as a slight warm sensation or a pinch in the treated
skin areas. This sensation can be an alert during application or for a few minutes after application.
Any sensation beyond this minimal annoyance is not normal and it means that you need to
interrupt the use because your skin is not able to tolerate epilation treatment, or the energy level
is too high.
Skin Redness
Skin may be reddened immediately after using appliance or during the following 24 hours. Redness
generally disappears within 24 hours. Consult your physician if the redness does not disappear
within 2 or 3 days..
Increased Skin Sensitivity
The skin of the treated area becomes more sensitive and can be dry or scaly.
Skin wounds and burns
Burns or wounds may occur after application. They may take a few weeks to heal, and, in very
rare cases, may leave a visible permanent scar.
Scars
Although it is very rare, permanent scars may be formed. Generally when scars are formed, they
have a flat lesion and white skin (hypertrophic). However, the scar may be very large and red
(hypertrophic) or large and extends beyond the margins of the wound itself (keloid). Subsequent
aesthetic treatments can be necessary to improve the appearance of the scar.
Pigmentation Changes
In some rare cases there is a risk of temporary pigmentation (greater pigment or
Brown bleaching) or IPO-pigmentation (whitening) in the surrounding skin area leeping. The risk
of skin pigmentation change is higher for people with dark skin complexion.
Redness and excessive swelling
In some rare cases the skin can become very red and swollen. This is more common in sensitive
areas of the body. Redness and swelling should decrease between 2 and 7 days later, it must be
cured with frequent applications of ice. You can gently wipe the area, but avoid exposing to the
sun.
Infection
Infection of the skin is very rare but it is a possible risk due to scalding or injury caused by the
device.
Bruises
Very seldom use of the device may cause blue-violet bruises that may last from 5 to 10 days.
15
NOTE:
Treating the same body part more frequently than recommended does not improve results. Due
to hormonal and physiological changes or other type, hair follicles, latents can become active.
Hair removal sessions or occasional maintenance treatment can therefore be necessary.
Individual reaction depends on hair type and biological factors that can affect the hair growth
cycle. Compared to the recommended epilation program, some people may react faster or
slower.
The appliance is not effective on very clear hair, on naturally white, gray, light blond and red hair
(see color scale on the packaging). If the hairs of your body are one of these colors, the device
will not be effective.
INSPECTION BEFORE USE
ENERGY LEVEL
he appliance can be set to 5 energy levels, from 1 (the
lowest) to 5 (the highest), represented by the 5 triangles
arranged like a fan on the status display (1). The energy
increases and decreases repeatedly pressing energy level
button (9) Increasing the power of treatment increases the
effectiveness of the CIA, but also possible side effects, it is
advisable to perform a patch test to identify the appropriate
energy level according to proper tolerance.
NUMEBER OF DISPOSABLE SPOTS
The meter reads the number of disposable spots available
to the light inserted. Spot counting is stored in an internal
chip in the light, then dismantling and reassembling the light,
the count is never lost, but reparts from the point where it
was left. Each light has its own count, when the light is 0, it
must be replaced.

ERROR MESSAGE

When the counter displays the message "error" instead of
the number of disposable spots, it means that the machine
cannot detect the light inserted. The problem may occur if
the light is not properly inserted, or if it is extracted while the
machine is running. If the light has been inserted correctly
and the message persists, it means that it is defective and
must be replaced.
f
f
f
16