Publicidad
Idiomas disponibles
Idiomas disponibles
3. Thread the nozzle adapter (packaged
with your tractor's Operator's Manual)
onto the end of your garden hose.
4. Pull back the lock collar of the nozzle
adapter and push the adapter onto the
deck washout port at the left end of the
mower deck. Release the lock collar to
lock the adapter on the nozzle.
IMPORTANT:Tug hose ensuring connec-
tion is secure.
5. Turn the water on.
Nozzle Ada
Washout Port
6.
While sitting
in the operator's
position
on
the tractor,
re-start
the engine
and place
the throttle
lever inthe
Fast ",,_" position.
IMPORTANT:
Recheck
the
area
making
certain
the area is clear.
7.
Movethe
tractor's
PTO (Blade Engage)
to
the ON position.
Remain
in the operator's
position
with the cutting
deck engaged
until the deck is cleaned.
8.
Move the tractor's
PTO (Blade
Engage)
to the OFF position.
Turn the ignition
key
to the STOP
position
to turn the tractor's
engine
off. Turn the water
off.
9.
Pull back
the lock collar
of the nozzle
adapter
to disconnect
the adapter
from
the nozzle
washout
port.
10. Move
the tractor
to a dry area,
prefer-
ably a concrete
or paved
area.
Engage
the mower
deck
PTO to remove
excess
water
and to help dry before
putting
the
tractor
away.
[&
WARNING:
A broken
or missing
washout fitting could expose you or
others to thrown objects from contact
with the blade.
• Replace
broken
or missing
washout
fitting
immediately,
prior
to
using
mower again.
• Plug any holes in mower
with bolts
and Iocknuts.
BATTERY
Your tractor
has a battery
charging
system
which
is sufficient
for normal
use.
However,
periodic
charging
of the battery
with an au-
tomotive
charger
will extend
its life.
•
Keep battery
and terminals
clean.
•
Keep battery
bolts tight.
• Keep small vent holes
open.
• Recharge
at 6-10 amperes
for 1 hour.
NOTE: The original equipment
battery on your
tractor
is maintenance
free.
Do not attempt
to open or remove
caps or covers.
Adding
or
checking
level of electrolyte
is not necessary.
TO CLEAN
BATTERY
AND TERMINALS
Corrosion
and dirt on the battery
and termi-
nals can cause
the battery
to "leak"
power.
1.
Disconnect
BLACK
battery
cable
first
then
RED
battery
cable
and
remove
battery
from tractor.
2.
Rinsethe
batterywith
plain water and dry.
3.
Clean
terminals
and battery
cable
ends
with wire brush
until bright.
4.
Coatterminals
with grease
or petroleum
jelly.
5.
Reinstall
battery
(See
"REPLACING
BATTERY"
in the SERVICE
AND
AD-
JUSTMENTS
section
of this manual).
TRANSAXLE
COOLING
The transmission
fan and cooling
fins should
be kept clean
to assure
proper
cooling.
Do not attempt
to clean fan or transmission
while
engine
is running
or while
the trans-
mission
is hot. To prevent
possible
damage
to seals,
do not use high pressure
water
or
steam
to clean
transaxle.
• Inspect
cooling
fan to be sure fan blades
are intact
and clean.
•
Inspectcooling
finsfordirt,
grass clippings
and other materials.
To prevent damageto
seals,
do not use compressed
air or high
pressure
sprayer
to clean
cooling
fins.
TRANSAXLE
PUMP FLUID
The transaxle
was sealed
at the factory
and
fluid maintenance
is not required
for the life
of the transaxle.
Should
the transaxle
ever
leak or require servicing,
contact
your nearest
Sears
or other
qualified
service
center.
V-BELTS
Check V-belts for deterioration
and wear after
100 hours of operation
and replace
if neces-
sary. The belts are not adjustable.
Replace
belts if they begin to slip from wear.
21
Publicidad
