Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Telephone Input Distribution Panel
To view installation video, pictures, descriptions, specifications, or instruction sheets for the
Telephone Input Distribution Panel, please visit our web site at: www.leviton.com.
WarnIngs anD CauTIons
• Follow all warnings and instructions marked on the product.
• Do not use or install in wet locations unless the components are designated specifically for
use in wet locations.
• Never push objects of any kind into this product through openings, as they may touch
dangerous voltages.
• Never install communications wiring or components during a lightning storm.
• Never touch uninsulated wires or terminals unless the wiring has been disconnected at the
network interface.
• Use caution when installing or modifying communications wiring or components.
• To prevent electrical shock, each opening must be filled with a module.
InTroDuCTIon
Application
Leviton's Telephone Input Distribution Panel (TIDP) is designed to connect telephone
services for home or small office cabling. The panel fits into Leviton's Structured Media
enclosures (SMC), featuring installer friendly Push-Lock Pin mounting. The TIDP provides
for standards compliant patching of the wall jacks to sources in the SMC and can be used
with various Leviton modules to provide for voice distribution. Route incoming telephone
service throughout the home or small office in up to four line applications using the 110
IDC, Voice Line Input Jacks, or a combination of both. Connect a security system to the
module via a dedicated Security Port, providing over-ride protection on the primary line in
case of emergency. The TIDP also features a Test Port and Auxiliary Disconnect Outlet
(ADO) allowing the user to isolate all internal telephone wiring and test the incoming phone
service from one central location.
Configuration
Telephone Input Distribution Panel (476TL-T12):
Features:
• 110 IDC Punchdown for basic phone, fax, modem service
• 4 Voice Line Input Jacks for connecting to analog telephone
jacks on a VoIP or Triple Play Modem
• Security Jack for Line Over-Ride and shorting plug
• Distributes up to 4 Lines of telephone service to up to
12 locations
Package Contents
The following items are included with your Panel:
• Telephone Input Distribution Panel
• Plastic 110 Termination Tool
• Four Push-Lock Pins and Grommets
• Twelve 8" 8p8c Flat Satin Patch Cables
• One 3" 8p8c Flat Satin Patch Cable (installed)
• Instruction Sheet
Required Tools
For wire termination the following tools are required:
• Angle cutters (if using the provided Plastic 110 Termination Tool)
• Professional Impact Tool with 110 Cutting Blade
• Wire Cutters
• UTP Wire Stripping Tool
TIDP
WITH
TRIPLE PLAY
VOICE INPUT
JACKS
VOICE LINE
INPUT JACKS
1
2
3
4
PK-93593-10-02-0A
®

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Leviton 476TL-T12

  • Página 1 InTroDuCTIon Application Leviton’s Telephone Input Distribution Panel (TIDP) is designed to connect telephone services for home or small office cabling. The panel fits into Leviton’s Structured Media ® enclosures (SMC), featuring installer friendly Push-Lock Pin mounting. The TIDP provides for standards compliant patching of the wall jacks to sources in the SMC and can be used with various Leviton modules to provide for voice distribution.
  • Página 2: Getting Started

    1) gETTIng sTarTED Planning Plan your cable routing carefully to determine the number of outlet locations required for phone, fax, and modem. Organize In the SMC, label the wires coming from your service provider and separate them from the voice and data wires running to your wall plates. Determine placement of the Panel. You will want to pick a spot next to the panel containing the jacks where your Structured Cabling is terminated in the SMC.
  • Página 3 Using Plastic Tool Provided: 1. Push the appropriate wire into the color designated 110 IDC slot with the tool (Figure 2). 2. Trim excess wire with diagonal cutters (Figure 3). Using professional Punch Tool: 1. Orient tool with cutting blade as shown (Figure 4). 2.
  • Página 4 Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is...
  • Página 5: Avertissements Et Mises En Garde

    • Afin d’éviter les chocs électriques, toutes les ouvertures doivent être occupées. InTroDuCTIon Applications Ces panneaux de distribution de Leviton sont conçus pour les raccordements téléphoniques de domiciles et de petits bureaux. Ils s'insèrent dans les centres Structured Media (centre médias structurés, ou CMS) grâce à des pattes de retenue expressément conçues pour faciliter la tâche des installateurs.
  • Página 6: Pour Commencer

    Outils requis Les outils suivants sont requis pour effectuer les terminaisons : • Coupe-fil biseauté (si on utilise l’outil en plastique fourni) • Percuteur professionnel et lame de type 110 • Coupe-fil • Dénudeur de PTNB 1) Pour CoMMEnCEr Préparation Planifier soigneusement le parcours des câbles en fonction du nombre de connexions requises pour le raccordement des services de téléphone, de télécopieur et de modem.
  • Página 7 Utilisation de l’outil en plastique fourni : 1. Enfoncer les fils dans les fentes au chromocodage approprié (figure 2); 2. Couper les longueurs excédentaires à l’aide d’un coupe-fil biseauté (figure 3). Utilisation d’un percuteur professionnel : 1. Orienter la lame de l’outil dans le sens indiqué (figure 4); 2.
  • Página 8 2 ans, à la Manufacture Leviton du Canada Limitée, au soin du service de l’Assurance Qualité, 165 boul. Hymus, Pointe-Claire, (Québec), Canada H9R 1E9.
  • Página 9: Panel De Distribucion De Entrada De Telefono

    El PDET cumple con los estándares de conexión de los jacks de pared de las fuentes del SMC y se pueden usar con varios módulos de Leviton para proveer distribución de voz. Guíe el servicio de entrada de teléfono al hogar u oficina hasta en cuatro líneas usando los IDC 110, jacks de entrada de línea de voz o combinación...
  • Página 10: Herramientas Requeridas

    Herramientas requeridas Para la terminación del alambre se requieren las siguientes herramientas: • Cortadores en ángulo (si está usando la herramienta de terminación de plástico 110, proporcionada) • Herramienta profesional de impacto con cuchilla de corte 110 • Cortadores de alambres •...
  • Página 11: Prueba Del Servicio De Telefono De Entrada

    Usando la herramienta de plástico proporcionada: 1. Empuje el alambre apropiado en la ranura del color señalado en IDC 110 con la herramienta (Figura 2). 2. Corte el exceso de alambre con los cortadores diagonales (Figura 3). Usando una herramienta profesional de insertar: 1.
  • Página 12 Leviton garantiza al consumidor original de sus productos y no para beneficio de nadie más que este producto en el momento de su venta por Leviton está libre de defectos en materiales o fabricación por un período de dos años desde la fecha de la compra original. La única obligación de Leviton es corregir tales defectos ya sea con reparación o reemplazo, como opción, si dentro de tal período de dos años el producto pagado se...

Tabla de contenido