Mounting Procedure; Power Cable Connection - Eaton EGS100L24R Manual Del Usuario

Instructional Booklet
Page 8 Effective: July 2008
Check to ensure there are no pipes, wires, or other mounting haz-
ards in the immediate mounting area that could create a problem.
Carefully remove all packing material from the ATS enclosure at
the installation site. Even though an equipment inspection was
performed when the equipment was received, make another care-
ful inspection of the enclosure and the ATS mechanism as the
packing material is removed and the enclosure readied for mount-
ing. Be especially alert for distorted metal, loose wires, or dam-
aged components.

4.3 Mounting Procedure

EXTREME CARE SHOULD BE TAKEN TO PROTECT THE ATS FROM
DRILL CHIPS, FILINGS, AND OTHER CONTAMINANTS WHEN MAK-
ING THE CABLE ENTRY HOLES AND MOUNTING THE ENCLOSURE
TO PREVENT COMPONENT DAMAGE OR A FUTURE MALFUNCTION.
THE INSTALLATION MUST FULLY COMPLY WITH ALL APPLICABLE
CODES, STANDARDS, AND REGULATIONS.
With the enclosed ATS equipment unpacked and ready for mount-
ing, proceed with the following steps.
For Type 3R:
Step 1: Depress the padlockable catch at the bottom of the door
and slide the door downward (see Figure 7). Open the
door and remove the deadfront.
Figure 7. Location of the Door Latch.
Step 2: Utilize the 5-point hanging system to mount..
FOR CONTROL WIRING (GENERATOR ENGINE START WIRING), THE
WIRES MUST BE ISOLATED FROM BOTH THE UTILITY AND GENERA-
TOR POWER SOURCE CABLES.
Step 3: Mount the switch to a rigid structure as close to the elec-
trical loads as possible.
CAUTION
NOTICE
NOTICE
For more information visit: www.eaton.com
O & M Manual for the EGS AutomaticTransfer Switch
with RTC-50 Control and Integral Loadcenter - 100 Amp

4.4 Power Cable Connection

POWER CONDUCTORS MAY HAVE VOLTAGE PRESENT THAT CAN
CAUSE SEVERE PERSONAL INJURY OR DEATH. DE-ENERGIZE ALL
POWER OR CONTROL CIRCUIT CONDUCTORS TO BE CONNECTED
TO THE ATS EQUIPMENT BEFORE BEGINNING TO WORK WITH THE
CONDUCTORS AND/OR TERMINATING THEM TO THE EQUIPMENT
TO HELP PREVENT COMPONENT DAMAGE OR FUTURE MALFUNC-
TIONS, USE EXTREME CARE TO KEEP CONTAMINANTS OUT OF
THE ATS EQUIPMENT WHEN MAKING THE POWER CABLE CONNEC-
TIONS.
Test all power cables prior to connection to the unit to ensure that
the conductors or cable insulation has not been damaged while
being pulled into position.
Power cables are to be connected to solderless, screw type lugs
located on the automatic transfer switching devices. Verify that
the lugs supplied will accommodate the power cables being used.
Also verify that the cables comply with all local electrical codes.
Standard ATS equipment, as supplied from the factory, will
accommodate the wire sizes shown in Table 2.
Table 2. Wire Sizes for ATSs.
TRANSFER SWITCH
AMP RATING
100
Carefully strip the insulation from the power cables to avoid nick-
ing or ringing of the conductor strands. Prepare the stripped con-
ductor termination end by cleaning it with a wire brush. If
aluminum conductors are used, apply an appropriate joint com-
pound to the clean conductor surface area.
IMPROPER POWER CABLE CONNECTIONS CAN CAUSE EXCESSIVE
HEAT AND SUBSEQUENT EQUIPMENT FAILURE.
Note:Tighten the cable lugs to the torque identified on the label affixed to
the unit.
Step 1: Connect cables as follows (see Figure 8 and Table 2):
• The utility power cables to the utility lugs;
• The generator power cables to the generator lugs;
• The customer load cables to the distribution panel;
• The neutral cables to the neutral bar; and
• The ground wires to the ground bar.
WARNING
CAUTION
CONTACTOR WIRE NUMBER OF CABLES
SIZE RANGE PER PHASE
#14 –2/0
CAUTION
1
IB70-8671