Safety Information; Caution; Obligations Of The Owner; Avoidance Of Danger - Grundfos AQC-D13 Instrucciones De Instalación Y Funcionamiento

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 42

7. Safety information

7.1 Obligations of the owner

The owner of the plant is responsible for
compliance with country-specific safety regulations
training of operating personnel
provision of prescribed protective gear
implementation of regular maintenance.

7.2 Avoidance of danger

Warning
Cleaning, maintenance and repairs must only be
carried out by authorised personnel!
Warning
Other applications than those described in section
6. Applications
are considered as non-approved and
are not permissible.
Derivates of chloro isocyanuric acid cannot be
measured or controlled.
Grundfos cannot be held liable for any damage
resulting from incorrect use.
8. Technical data

8.1 General data

The AQC-D13 is an unpressurised measuring cell with
hydromechanical cleaning and open outlet of sample water.
Measuring parameters:
– free chlorine, chlorine dioxide, ozone
– optional: pH value, redox potential, temperature
(for compensation of pH, Cl
Sample water:
– free of solids
– min. conductivity: 50 µS/cm
– temperature: 0-40 °C
– pH value (only measuring parameter Cl
– inlet pressure: max. 6 bar, min. 0.2 bar
– counterpressure: p
(open outflow).
amb
Permissible ambient temperature: 0 to 45 °C.
Permissible storage temperature:
– -20 to +65 °C
– Electrodes: -10 to +30 °C.
Observe the installation and operating instructions of

Caution

the electrodes!
Permissible humidity: max. 90 % relative humidity
(without condensation).
Sample water flow rate: approx. 15 l/h.
Materials of parts that come into contact with the media:
PMMA, PVC, EPDM.
Electrode materials: gold, platinum, glass, nickel, PVC.
Connections:
– inlet: for PVC hose 6/12 or PVC pipe 12 x 1.2
– outlet: for PVC hose 12/16.
, ClO
, O
).
2
2
3
): pH 4.5 - 8.2
2
Measuring parameters: chlorine, chlorine dioxide and ozone
Measuring ranges: Dependent on the measuring amplifier.
See section
8.3.1 Measuring ranges for Cl
ORP.
Sensitivity: < 10 ppb.
Accuracy: < - 5 %/+ 5 % of full-scale value.
Repeatability: < - 5 %/+ 5 %.
Response time: t
< 60 s.
90

8.2 Versions

Power supply:
– 230/240 V, 50/60 Hz (standard)
– 115/120 V, 50/60 Hz
– 24 VDC (not with DIP).
Equipment / options:
– gold electrode for free chlorine, chlorine dioxide, ozone
(standard)
– platinum electrode
– redox single-rod measuring chain (electrode)
– redox electrode (with DIP)
– pH single-rod measuring chain (electrode).
8.2.1 AquaCell AQC-D13
Cables:
– connecting cables for the electrodes, 3 m, with free cable
end
– cable for measuring electrode, 3 m, with free cable end.
Options:
– water sensor with cable, 3 m.
– Pt100 temperature sensor with cable, 3 m.
8.2.2 Preassembled systems
Cables:
– connecting cables for the electrodes, 1 m, preconnected
– cable for measuring electrode, 1 m, preconnected.
Options:
– water sensor with cable, 1 m.
– Pt100 temperature sensor with cable, 1 m.
Product numbers of the spare parts and optional accessories, see
section
14. Spare parts and
accessories.
, ClO
, O
, pH,
2
2
3
9

Publicidad

Tabla de contenido
loading

Tabla de contenido