Switching A Call From Headset To Desk Telephone Handset; Switching A Call From Desk Telephone Handset To Headset; New Master Headset Pairing To Base; Establishing A Clean Audio Mode Link - Jabra GN9300e Manual De Usuario

GN9350e GN9330e GN9330e USB

4.5 Switching a call from headset to desk telephone handset

It's possible to switch a call in progress from the headset to the telephone's handset:
1. Lift the telephone's handset to your ear.
2. Do one of the following:
• Place the headset into the charging cradle.
• Press the headset's talk button.
• Press the base's telephone mode button.
–> The headset's link indicator will stop flashing to indicate that the headset-base link
has been closed.
Important: If using electronic hookswitch on your telephone, do not place the headset into
the charging cradle, and do not press the headset´s talk button or press the base´s telephone
mode button, as this will disconnect the call.
If the headset runs out of battery power, the headset-base link will remain active for up to 2
minutes to allow for battery changing.
GN9350e GN9330e GN9330e USB

4.6 Switching a call from desk telephone handset to headset

It's possible to switch a call in progress from the telephone's handset to the headset:
1. Remove the headset from base, or if already out, press
the headset's talk button. This establishes a link.
–> The headset's link indicator will start flashing and the
call will be switched to the headset.
Note: Do not place handset before the call is over, as this will end the call.
GN9350e GN9330e GN9330e USB

4.7 New master headset pairing to base

You may designate a new master headset for your base.
Important: Before designating a new master headset, ensure that the original headset's link
to the base unit is closed by pressing its talk button. The telephone or USB indicator should
not flash.
To designate a new master headset:
1. Place the new master headset into the charging cradle of the base.
2. Press the base's pairing button.
14
–> Both the telephone and USB mode buttons on the
base, and the headset's link indicator, will light for
2 seconds. This indicates successful pairing of the
new master headset.
GN9350e GN9330e GN9330e USB

4.8 Establishing a Clean Audio Mode link

In the PC phone (VoIP) use case many Unified Com-
munication applications (e.g. Cisco IP Communicator
or Microsoft Office Communicator) deliver voice mails
in the inbox of the e-mail application (e.g. Outlook).
Further, many users have a separate application for conference calls (with or without video).
In these use case it is also very relevant to use your headset.
In situations where other applications than the PC phone appli-
cation wants to use the headset (as just described), you need to
establish a Clean Audio Mode link without triggering the soft phone
hook-off command.
The Clean Audio Mode functionality is implemented as a double-tap
on the headset's talk button.
For example, if you want to participate in a conference call or listen to a voice-mail delivered
by email, simply activate the Clean Audio Mode by double-tapping the headset's talk button
on the headset. When ending the conference call just single tap the headset's talk button to
close the Clean Audio Mode.
Note that you have to set the Audio Preference in the Windows operation system to the GN9330e or
GN9350e. Also, in the conference call application (e.g. Windows Live Meeting), you have to set the
Audio preferences to the GN9330e or GN9350e.

5. Use with DECT cordless telephones

GN9350e GN9330e GN9330e USB
Your headset can also be used with DECT cordless telephones (Digital Enhanced Cordless
Telecommunication), which are GAP-compatible (Generic Access Profile). You must first pair
the headset to the base unit of the cordless telephone.
Important: Your headset's authentication code is 0000, which is the same code as for most DECT
cordless telephones. Your headset will only work with cordless telephones with the 0000 code.
2
15
1