RIDGID RP 100-B Instrucciones De Operación página 3

RP 100-B, RP 300-B
TROUBLESHOOTING
LED display
Acoustics
green red yellow
RP 100-B and RP 300-B
lit lit lit short beep ON/OFF switch
(300-B)
lit – – –
lit – blinks –
20,000 pressings
lit blinks – –
lit blinks – – Temperature out
– lit lit beeps
5 sec.
(300-B)
RP 300-B ONLY
blinks
– – –
3 times
– – lit –
RP 100-B ONLY
blinks blinks – – Low battery tool
lit – lit –
• If there is a power supply interruption during pressing procedure, the
machine stops and the pistons will be brought into the original position
after a few seconds.
Note:- for 100-B press black release button on side of tool.
• Whenever a pressing cycle is not fully completed the complete procedure
must be repeated.
• It is strongly recommended to never attempt to repeat a pressing cycle
that has been interrupted. This may lead to damage to the joint and pos-
sible leakage. The joint should be cut out and replaced by a new one.
2
Status Action
Machine –
being pressed activated
All O.K. –
All O.K. after Service Inspection and main-
required tenance by authorized
service center
Retaining bolt Machine Insert retaining bolt
not inserted blocked correctly
completely
Machine Bring machine within
of range blocked temp. range of -5°C
and +50°C
6 consecutive Machine Inspection and main-
times pressure blocked tenance by authorized
not reached or = service service center
time exceeded
Pressing O.K. –
Maintenance Machine Inspection and main-
after 22,000 blocked tenance by authorized
pressings service center
Replace or recharge
overheated or battery. Allow tool to
excess current cool. If condition repeats
inspection by authorized
service center
Maintenance Machine Inspection and main-
after 22,000 blocked tenance by authorized
pressings service center
Ridge Tool Company
• The use of jaws not specifi cally designed for pressing the fi ttings being
used may lead to damage and incorrectly compressed fi ttings. Contact
your RIDGID Press Fit Service Centre for any malfunction not covered in
this instruction manual.
MAINTENANCE
Always remove the battery before performing any maintenance.
Daily
- Clean the Press Fit tool with a soft cloth. Do not use detergents to clean
the crimping tool. Check the condition of the tool and ensure that the
press rolls (Fig.1, ref. 6) are free of metallic particles. Use lubricating and
corrosion prevention spray if they appear dry.
Every 20,000 pressings (or every 3 years)
- The Press Fit tool must be sent for inspection and maintenance to the
nearest authorized RIDGID Press Fit repair centre. After 20,000 cycles a
warning signal will indicate that the tool should be serviced (see trouble-
shooting).
- The repair centre will fully overhaul the tool and inspect that it is opera-
ting correctly.
- Any unauthorized modifi cations and/or repairs will invalidate the warranty.
Storage
- Before storing the tool for long periods clean the tool thoroughly and wipe
clean.
- Keep the tool away from moisture and heat, and do not expose the tool
to extreme temperatures.
- Keep away from children.
- The RIDGID Press Fit tool is made of numerous metal and plastic parts.
Ensure that the tool is correctly disposed of in accordance with local
regulations.
Fig. 1
1 ON/OFF switch
2 LED display green, red and orange
3 Trigger switch – starts automatic pressing cycle
4 Tool identifi cation plate with serial number
5 Press jaw holder with 90° rotation
6 Press rolls
7 Lock pin
8 Press jaw
9 Plastic housing
10 Battery 14.4 V / 2.6 Ah
WARNING!
Keep fi ngers and hands away from jaws during
pressing cycle!
Fingers or hands can be crushed, fractured or
amputated if they become caught between the jaws.
Always verify that the jaw is correctly fi tted in the
press tool and that the locking pin is fi rmly closed.
IMPORTANT:
This jaw set is designed to make Press Fit connections for the specifi c
system and size noted on the jaw set and packaging.
Follow fi tting manufacturer's recommendations on proper installation.
The use of incorrect jaw sets for a system or size will result in an
improper seal that could result in extensive property damage.