Publicidad
Idiomas disponibles
Idiomas disponibles
interval setting mode. The setting always starts from 00:00 and
the first time with the day mode, indicated by a lit G icon. Press
keys C and D to increase or decrease the time shown on the
display by intervals of 15 minutes and press key B to modify the
operating mode from day to night and vice versa. To adjust the
intervals, you must select whether the machine should be in
night or day mode at 00:00 by pressing key B and then press
key C until you reach the time you want to change mode. Now
press key B to switch mode and the icon comes on to indicate
that the mode has changed. Scroll backwards and forwards
using keys C and D to check the switching time intervals. You
can set mode switching for every 15 minutes. When you reach
23:45 press key C again to quit the switching time interval set-
ting.
If the 12 hr mode has been selected, A or P is indicated on the
third or fourth figure (denoting AM or PM).
TIMER ON/OFF
If you press key D for 5 seconds when the machine is in
Standby mode, the day/night timer is activated. The icon N indi-
cates the state of the timer. The default value the first time the
machine is switched on is timer OFF.
NOTE: The keypad lock also has affects the Standby mode
and therefore the possibility of adjusting the clock.
TEMPORARY SUSPENSION OF TIMER
When the timer is activated and the machine is operating in Day
Mode, the timer can be temporarily suspended so that the oper-
ating mode can be manually adjusted. To do this, hold down the
night key for two seconds, when the timer icon flashes you can
select the Night Mode or Cleaning on any bowl. Press the day
key again to reactivate the timer.
6. 2 ADDITIONAL FUNCTIONS
LIGHT SWITCHING ON/OFF
By pressing key standby (B) twice quickly, lights can be turned
on and off. When the machine is in the Granita Making mode,
lights are always on; when the machine is in the Product Pres-
ervation mode, lights are always off.
DENSITY ADJUSTMENT
When the machine is working in the Granita Making mode, it is
possible to adjust product density by pressing keys C or D brief-
ly.
The factory set value is 5, which is recommended to make grani-
tas.
WASHING MODE
When the dispenser is in the Product Preservation mode, by
pressing key C for two seconds, the Washing mode is enabled.
In such a case, the auger turns but cooling is disabled.
Use this mode during the machine washing and sterilization to
prevent the cleaning solution from cooling.
By pressing any key, the dispenser exits from the Washing
mode and returns to the Product Preservation mode.
ALARM DISPLAY
If a fault occurs during the dispenser operation, an alarm mes-
sage is displayed. One of the elements on the density bar hop-
per flash showing the corresponding alarm number. To find a
detailed alarm list, please refer to the Service Manual.
COMPRESSOR CONDITION
The compressor condition is shown above the first density bar
of the right bowl:
- Off: compressor off
- Flashing: start delay timer on
- On: compressor on
TOUCHPAD LOCK
It is possible to lock the touchpad to prevent access to the dis-
penser controls by keeping keys C and D pressed together for
two seconds.
By pressing keys C and D at the same time again, the touchpad
is unlocked.
6. 3 OPERATION HELPFUL HINTS
1 The time required to make servable product varies
depending on several factors such as the ambient temperature,
the initial temperature of the product, its sugar content (degrees
Brix) and fat content and the density adjustment.
2 Filling the bowls with product that is already pre-cooled
further increases the efficiency of the dispenser.
3 To further reduce recovery time, refill the bowls when the
level of product is below the halfway point of the evaporator.
4 To store the product correctly, the dispenser must also
operate at night, at least in the PRODUCT STORAGE position.
5 Night operation in the PRODUCT STORAGE position also
eliminates the possible formation of ice (due to condensation of
atmospheric moisture) on the outside of the bowls.
6 Never turn off the dispenser when there is product in the
bowls. If not cooled, the product may deteriorate. Furthermore,
unless it is mixed, it may stick together and form blocks of ice. If
the mixer is restarted in these conditions (without waiting for the
ice to melt), the dispenser may be damaged.
7 All dispensers of this kind emit heat. If, however, this
emission seems excessive, check that no source of heat is
located near the dispenser itself and, in particular, near the
louvered panels. Also make sure that the airflow is not impeded
by the proximity of walls, boxes or similar. Leave at least 6" free
space around the dispenser. Finally, check that the filter
located behind the rear panel is clean.
ATTENTION
The access to the service area is restricted to persons
having safety/hygiene knowledge and practical experi-
ence on the dispenser.
8 The product is for use with confectionery drinks only.
6. 4 CLEANING
1 Cleaning and washing are essential to guarantee the
perfect preservation of the taste of the product and the
maximum efficiency of your dispenser. The procedures
described below should be considered general in nature and
may vary due to local health regulations.
2 Before disassembly for washing, the dispenser must be
emptied. Proceed as follows:
-
use the touchpad to select the CLEANING operating mode
-
if necessary, wait until the product becomes liquid
-
remove the flow restrictor from the bowl (see figure 8)
-
place a bucket under each spigot and empty the bowls
-
fill the bowls with water and allow the dispenser to operate
in CLEANING mode for a few minutes. Then empty the bowls.
-
hold down key A to switch off the dispenser
-
turn the main power switch OFF
5
Publicidad
