Communicator Status Leds; Yellow Trouble Led - DSC GS2060 Manual De Instalación Y Del Operario

Manual de instalacion

Ocultar thumbs Ver también para GS2060:

Manual de instrucciones (81 páginas)

Manual de instrucciones (60 páginas)

Tabla de contenido

Idiomas disponibles

3. Connect24 will confirm that the account has DLS service and will provide the Public IP address and port

number of the DLS server in the SMS message.

4. SMS message will establish a connection to your computer's DLS IV software (programming labels only).

5. Create an account for the Panel/Communicator, select the Communicator type (e.g., SMS - TL260GS) and

enter all relevant information in SMS section.

NOTE: The GSM telephone number will also be required by the users, to send SMS Command and Con-

trol messages to their system.

6. Program the account information, then click Global Download and choose SMS as the Connection Type.

Click OK.

7. The download path configured in Communicator Programming Section [005] Option[4] determines the

GPRS or Ethernet path to be used.

The Communicator has 4 onboard LED indicators. These include 1 yellow trouble LED, 1 red Network Connec-

tion Status LED, and 2 green Signal Strength LEDs.

Yellow Trouble LED

This yellow LED will flash to indicate a trouble on the unit. The number of flashes indicates the type of trouble.

See the table below for the coded flashes and the conditions which will activate the Trouble Status LED.

# OF

FLASHES

Panel Supervision Trouble

Receiver Not Available Trouble

NOTE: Only the highest priority trouble (1 Flash is highest priority) is indicated. When this trouble is

restored, the next highest trouble will indicate, if present. This will continue until all Troubles have been

cleared (yellow LED OFF).

The following paragraphs describe the conditions associated with the trouble indicated:

Panel Supervision Trouble (2 Flashes)

This trouble will be indicated when communication between the Communicator module and the control panel

fails. If the module can not communicate with the panel (e.g., loss of power to the panel) the Communicator will

send the 'Panel Absent Trouble Event' message to the central station receiver. When communication returns, a

'Panel Absent Restore Event' is sent by the Communicator to the central station receiver. The reporting codes

are ET0001 for Trouble and ER0001 for Restore. The panel absent event always uses the primary receiver

account code when communicating to the central station.

NOTE: The Panel Supervision Trouble/Restore is an internally generated event by the Communicator. It is the only internal

event; all other events are generated by the control panel. Trouble is generated if the Communicator misses 3 Polls

(PC9155) or 6 Polls (PC1864). Trouble is restored on receipt of first Poll from the panel.

SIM Lock Trouble (4 Flashes)

This trouble will signify that the SIM lock feature has been enabled and the unit has not been programmed with

the correct PIN for the SIM card.

GSM Trouble (5 Flashes)

This trouble is indicated for any of the following 4 conditions:

a. Radio Failure:Trouble is indicated after 8 failed attempts to communicate with the GSM radio.

b. SIM Failure:Trouble is indicated after 10 failed +CPIN commands.

c. GSM Network Trouble:Trouble is indicated for loss of the registration to the network provider. (3 consec-

utive init or refresh failures, failure to connect to an APN, failure to open a socket, total error count in

cyclic command = 20, or on receiving an MSDI (1/2), (7/8/14). Trouble will clear after init and cyclic com-

mands succeed and MIPCALL and MIPOPEN commands succeed.

d. Insufficient Signal Strength: Trouble is indicated if calculated average signal strength is too low. (Both green

LEDs OFF). Trouble will clear when the calculated average signal strength is above minimum (i.e., > CSQ 5) .

Ethernet Trouble (6 Flashes)

This trouble is indicated when Ethernet link between the transmitter and the local hub or router is absent.This

trouble will also be indicated if the unit fails to get Dynamic Host Control Protocol (DHCP) settings from the

DHCP server. (Not active if Ethernet Receivers are not programmed).

Receiver Not Available (7 Flashes)

This trouble is indicated if the unit is not able to successfully initialize with any of the programmed receivers.

Unprogrammed receivers are excluded. This trouble is also indicated if the GPRS receiver APNs have not been

programmed in Sections [205] and [215].

Receiver Supervision Trouble (8 Flashes)

This trouble is indicated when receiver supervision is enabled and communication between the Communicator

module and the receiver fails.Trouble is indicated if Ethernet 1 is supervised and does not receive a heartbeat

from the receiver or if GPRS is supervised and the unit does not receive an acknowledgment to 4 heartbeats

sent to the receiver.

FTC Trouble (9 Flashes)

This trouble is indicated when the unit fails to communicate module events to the central station.Trouble is dis-

played after the unit has exhausted all communications attempts to all programmed receivers for events gener-

ated by the Communicator.

Connect24 Configuration Failure (10 Flashes)

This trouble is indicated when the unit fails to receive programming from Connect 24.