Descargar Imprimir esta página

Bostitch BT125 Manual De Operación Y De Mantenimiento página 9

Engrapadoras neumaticas

Publicidad

Idiomas disponibles

Idiomas disponibles

TOOL
OPERATION
I_WARNING:
]
EYE PROTECTION which conforms to ANSI specifications
and provides protection against
flying
particles both from the FRONT and SIDE should ALWAYS be worn by the operator
and others in the work area when connecting to air supply, loading, operating or servicing
this tool. Eye protection is required to guard against flying fasteners
and debris, which
could cause severe eye injury.
The employer and/or user must ensure that proper eye protection is worn. Eye protection
equipment must conform to the requirements of the American National Standards Institute,
ANSI Z87.1
and provide
both frontal
and
side protection.
NOTE:
Non-side
shielded
spectacles and face shields alone do not provide adequate protection.
BEFORE HANDLING OR OPERATING THIS TOOL:
I.
READ AND UNDERSTAND THE WARNINGS CONTAINED IN THIS MANUAL.
II.
REFER TO "TOOL SPECIFICATIONS"
IN THIS MANUAL TO IDENTIFY THE
OPERATING SYSTEM ON YOUR TOOL.
There are three available systems on BOSTITCH
pneumatic
tools. They are:
1. CONTACT TRIP OPERATION
2. SEQUENTIAL
TRIP OPERATION
3. TRIGGER
OPERATION
OPERATION
1.
CONTACT TRIP OPERATION:
The CONTACT
TRIP MODEL tool contains a contact trip that operates in conjunction
with the trigger to
drive a fastener. There are two methods of operation to drive fasteners
with a contact trip tool.
A. SINGLE FASTENER
PLACEMENT:
To operate the tool in this manner, first position the contact trip
on the work surface, WITHOUT
PULLING
THE TRIGGER.
Depress the contact trip until the nose
touches the work surface and then pull the trigger to drive a fastener. Do not press the tool against
the work with extra force. Instead, allow the tool to recoil off the work surface to avoid a second
unwanted fastener.
Remove your finger from the trigger after each operation.
B. RAPID FASTENER
OPERATION:
To operate the tool in this manner, hold the tool with the contact
trip pointing towards but not touching
the work surface. Pull the trigger and then tap the contact trip
against the work surface
using a bouncing
motion. Each depression
of the contact trip will cause a
fastener to be driven.
LAWARNmG:J
L._wA,,e,_oJ
L_wAe,e,_:J
The operator must not hold the trigger pulled on contact trip tools except during fastening
operation,
as serious
injury could result if the trip accidentally
contacted
someone
or
something, causing the tool to cycle.
Keep hands and body away from the discharge area of the tool.
A contact trip tool may
bounce from the recoil of driving a fastener
and an unwanted second fastener
may be
driven, possibly causing injury.
Never use belt hook with contact trigger (black trigger) operated tools.
2. SEQUENTIAL
TRIP OPERATION:
The SEQUENTIAL
TRIP MODEL contains
a contact trip that operates
in conjunction
with the trigger to
drive a fastener.
To operate
a sequential
trip tool, first position
the contact
trip on the work surface
WITHOUT
PULLING
THE TRIGGER.
Depress
the contact
trip and then pull the trigger
to drive a
fastener.
As long as the contact trip is contacting
the work and is held depressed,
the tool will drive a
fastener
each time the trigger is depressed.
If the contact trip is allowed to leave the work surface, the
sequence
described above must be repeated to drive another fastener.
3. TRIGGER
OPERATION:
ATRIGGER
OPERATED
tool requires a single action to drive a fastener.
Each time the trigger is pulled
the tool will drive a fastener.
The trigger operated
model is intended for use only when a contact trip or
sequential
trip cannot be used due to the requirements
of the application.
-9-

Publicidad

loading

Este manual también es adecuado para:

Bt200Sl150Sx150Lhf97125Sx150-bhfS97125 ... Mostrar todo