Canon imageCLASS MF4890DW Guia De Inicio Rapido página 20

Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See the
e-Manual for specifi c dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2. Order an RJ11-C telephone wall jack (USOC), which should be
installed by the telephone company. If the RJ11-C wall jack is not
present, telephone/facsimile operation is not possible.
3. Order a normal business line from your telephone company's
business representative. The line should be a regular voice grade
line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate
overseas
NOTE
Canon recommends an individual line following industry standards,
i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial) telephones. A
dedicated extension off a PBX (Private Branch eXchange) unit
without "Call Waiting" can be used with your facsimile unit. Key
telephone systems are not recommended because they send
nonstandard signals to individual telephones for ringing and special
codes, which may cause a facsimile error.
C. Power Requirements
The machine should be connected to a standard 120 volt AC,
threewire grounded outlet only.
Do not connect this machine to an outlet or power line shared with
other appliances that cause "electrical noise." Air conditioners,
electric typewriters, copiers, and machines of this sort generate
electrical noise that often interferes with communications equipment
and the sending and receiving of documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the rear panel of this
equipment is a label that contains, among other information, a
product identifi er in the format of US:AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
The REN (Ringer Equivalence Number) is used to determine the
number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas, the
sum of the RENs should not exceed fi ve (5.0).
To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone
company. The REN for this product is part of the product identifi er
that has the format US: AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is provided
En
with this equipment. This equipment is designed to be connected to
the telephone network or premise wiring using a compatible modular
jack that is Part 68 compliant.
This equipment may not be used on coin service provided by the
telephone company. Connection to party lines is subjected to state
tariff s.
20
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected by the
procedures described in this guide or the e-Manual, disconnect the
equipment from the telephone line cable and disconnect the power
cord.
The telephone line cable should not be reconnected or the power
switch turned ON until the problem is completely resolved. Users
should contact Canon Authorized Service Facilities for servicing
of equipment, Information regarding Authorized Service Facility
locations can be obtained by calling Canon Customer Care Center
(1-800-OK-CANON).
Rights of the Telephone Company
If this equipment (imageCLASS MF4890dw/MF4880dw/MF4770n)
causes harm to the telephone network, the telephone company may
temporarily disconnect service. The telephone company also retains
the right to make changes in facilities and services that may aff ect
the operation of this equipment. When such changes are necessary,
the telephone company is required to give adequate prior notice to
the user.
However, if advance notice is not possible, the telephone company
will notify the customer as soon as possible. Also, the customer will
be advised of his/her right to fi le a complaint with the FCC if he/she
believes it is necessary.
WARNING
The Telephone Consumer Protection Act of 1991 makes it unlawful
for any person to use a computer or other electronic device, including
FAX machines, to send any message unless such message clearly
contains in a margin at the top or bottom of each transmitted page or
on the fi rst page of the transmission, the date and time it is sent and
an identifi cation of the business or other entity, or other individual
sending the message and the telephone number of the sending
machine or such business, other entity, or individual. (The telephone
number provided may not be a 900 number or any other number for
which charges exceed local or long-distance transmission charges.)
NOTE
In order to program this information into your machine, you should
complete the procedure for registering your name, unit's telephone
number, time, and date in the Starter Guide.
Users in Canada
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See the
e-Manual for specifi c dimensions and weight.
B. Order Information
1. A single telephone line (touch-tone or rotary) should be used.
2. Order a CA11A modular jack, which should be installed by the
telephone company. If the CA11A jack is not present, installation
cannot occur.
3. Order a normal business line from your telephone company's
business representative. The line should be a regular voice grade
line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate
overseas
NOTE
Canon recommends an individual line following industry standards,
i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial) telephones. A
dedicated extension off a PBX (Private Branch eXchange) unit
without "Call Waiting" can be used with your facsimile unit. Key
telephone systems are not recommended because they send
nonstandard signals to individual telephones for ringing and special
codes, which may cause a facsimile error.