Model Hc-450 Description, Specifications And Standard Equipment Description; Specifications; Standard Equipment - RIDGID HC-450 Manual Del Operador

HC-450/HC-300 Hole Cutting Tools
existing system, the pipe must be drained and de-
pressurized prior to cutting. This reduces the risk of
electrical shock and other serious injury.
• Before using, test the Ground Fault Circuit Inter-
rupter (GFCI) provided with the power cord to in-
sure it is operating properly. GFCI reduces the risk
of electrical shock.
• When working overhead, all personnel should
wear hard hats and be clear of the area below the
tool. This reduces the risk of serious injury should
objects fall.
• Only use Hole Cutting Tools to cut holes in pipe as
directed in this manual. Do not use for other purposes
or modify. Other uses or modifying this tool for other
purposes may increase the risk of serious injury.
• Read and understand the instructions and warn-
ings for all equipment being used before operating
the Hole Cutting Tool. Failure to follow all instructions
and warnings may result in property damage or serious
personal injury.
Some dust created by power sanding,
WARNING
sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth de-
fects, or other reproductive harm. Some examples of
these chemicals are:
• Lead from lead based paint
• Crystalline silica from bricks and cement and other
masonry products, and
• Arsenic and chromium from chemically treated lum-
ber
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those
dust masks that are specifically designed to filter out
microscopic particles.
The EC Declaration of Conformity (890-011-320.10) will
accompany this manual as a separate booklet when re-
quired.
If you have any question concerning this RIDGID
uct:
– Contact your local RIDGID distributor.
– Visit www.RIDGID.com or www.RIDGID.eu to find
your local RIDGID contact point.
– Contact RIDGID Technical Services Department at
rtctechservices@emerson.com, or in the U.S. and
Canada call (800) 519-3456.
4
Model HC-450 Description,
Specifications And Standard
Equipment
Description
The RIDGID
signed to cut holes up to 4
hole sizes allow the use of Mechanical T's
O-Lets™, and other fittings for branching unpressurized
pipe lines.
The HC-450 has a
all sizes of hole saws and hole saw arbors. An integral
motor and gear reduction optimizes performance of large
diameter hole saws. The two feed handles allows the op-
erator to use the Hole Cutting Tool from either the left or
right side. A rotating leveling vial in the base allows re-
peated holes to line up. Only 13" high, the compact design,
allows the HC-450 to be used in tight quarters or above in-
stalled pipe close to ceilings.
NOTE! Mechanical T's, Hookers, and Vic-O-Lets are
registered trademarks of Victaulic Tool Company

Specifications

Cutting Capacity ............Up to 4
Pipe Mounting
Capacity ........................1
Drill Chuck Capacity ......
Drill Chuck Speed..........110 RPM
Motor Horsepower.........1.2 HP
Current Draw Rating......12 Amps @ 115V
Dimensions
Height ............................12.62" (29 cm)
Length ...........................17" (43 cm)
Width .............................17" (43 cm)
® prod-
Weight ............................42 lbs. (19 Kg)

Standard Equipment

• Hole Cutting Tool
• Chuck Key
• 5 / " Hole Saw Arbor w/Backing Plate and
8
Model HC-450 Hole Cutting Tool is de-
®
3 / " into steel pipe. The multiple
4
5 / " capacity drill chuck to accommodate
8
3 / " (120 mm)
4
1 / " - 8" (30mm-200 mm)
4
1 / " - 5 / " (2mm-16 mm)
16 8
6 Amps @ 230V
12 Amps @ 100V
® , Hookers ® , Vic-
1 / " Pilot Drill
4