Publicidad
Idiomas disponibles
Idiomas disponibles
POSiTiONiNG
THE
HANDLEBARS
1.
Loosen the two knobs on the
Handlebar Knob
_
inside of the handlebars (Fig. 1).
2.
With the unit upright, swing
the handlebars
up into the
operating position (Fig. 2).
NOTE:
Take care not to pinch
the throttle cable or
switch wires when
positioning
the
handlebar.
3.
Tighten the knobs to secure
the handlebars
in place.
NOTE:
Do not over-tighten
the
knobs.
4.
Reconnect the spark plug
wire to the spark plug.
ADJUSTING
TINE DEPTH
To adjust the wheel support
bracket proceed as follows:
1.
Stop engine and disconnect
spark plug to avoid
accidental
starting.
2.
Remove clip from the cotter
pin and slide clevis pin out of
tailpiece bracket (Fig. 3).
3.
Slide the wheel support
bracket up or down in the
tailpiece, aligning the holes
to the desired tine depth.
4.
Place the cotter pin through
the hole and secure with clip.
Was"e I
Fig. 1
Fig. 2
Wheel Supprt
Bracket
Cotter
Pin
Bolt
/
Wheem
Bracket
Fig. 3
WARNING:
OVERFILLING OIL CRANKCASE
MAY CAUSE
SERIOUS PERSONAL INJURY. Check and maintain the proper oil
level in the crankcase; it is important and cannot be
overemphasized.
Check the oil before each use and change it as
needed. See Changing the Oil.
RECOMMENDED
OiL TYPE
Using the proper type and weight of oil in the crankcase is extremely important.
Check the oil before each use and change the oil regularly. Failure to use the
correct oil, or using dirty oil, can cause premature engine wear and failure.
Use a high-quality SAE 30 weight oil of API (American Petroleum Institute)
service class SF, SG, SH.
ADDING OiL TO CRANKCASE:
iNiTiAL
USE
NOTE:
This unit is shipped
without oil. In order to
avoid damage to the
unit, put oil in the
crankcase before
attempting to start the
unit.
The unit is supplied with one 3.04
fluid oz. (90 ml.) bottle of SAE 30
SF, SG, SH oil (Fig. 4).
NOTE:
Save the bottle of oil. It
can be used to measure
the correct amount
during future oil
changes. See Changing
the Oil.
1.
Unscrew the top of the bottle
of oil and remove the paper
seal covering the opening.
Replace the top. Next, cut the
tip off the funnel spout (Fig. 4).
oil Fill Hole
2.
Place unit on a flat, level
surface.
Fig. 5
3.
Remove the oil fill plug from the crankcase (Fig. 6).
Fig. 4
4.
Pour the entire bottle of oil into
the oil fill hole (Fig. 5).
Oil Fill Plug \
NOTE:
Never add oil to the fuel
or fuel tank.
5.
Wipe up any oil that may
have spilled and reinstall the
oil fill plug.
O-Ring
Check oil before each use and
change as needed. Refer to
Oil Fill
Checking the Oil Level.
Hole
RECOMMENDED
FUEL TYPE
Old fuel is the primary reason for
Fig. 6
improper unit performance.
Be
sure to use fresh, clean, unleaded gasoline.
NOTE:
Dispose of the old gasoline in accordance
to Federal, State and
Local regulations.
NOTE:
This is a four cycle engine. In order to avoid damage to the unit, do
not mix oil with gasoline.
Definition
of Blended
Fuels
Today's fuels are often a blend of gasoline and oxygenates such as ethanol,
methanol or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate or form acids when stored.
Use fresh fuel (less than 60 days old), when using alcohol-blended
fuel.
Using Blended Fuels
If choosing to use a blended fuel, or its use is unavoidable,
follow
recommended
precautions:
• Always use fresh unleaded gasoline
• Use the fuel additive STA-BIL® or an equivalent
• Drain tank and run the engine dry before storing unit
Using Fuel Additives
WARNING:
Gasoline is extremely flammable.
Ignited vapors
i _
may explode. Always stop the engine and allow it to cool before
filling the fuel tank. Do not smoke while filling the tank. Keep
i
sparks and open flames at a distance from the area.
i
i
WARNING:
Add fuel in a clean, well ventilated
outdoor area. Wipe
i _
up any spilled fuel immediately. Avoid creating a source of ignition for
spilt fuel. Do not start the engine until fuel vapors dissipate.
1
1
The use of fuel additives, such as STA-BIL® Gas Stabilizer or an equivalent, will
inhibit corrosion and minimize the formation of gum deposits. Using a fuel additive
can keep fuel from forming harmful deposits in the carburetor for up to six (6)
months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel according to the
instructions on the fuel additive container. NEVER add fuel additives directly to the
unit's gas tank.
FUELING THE UNIT
_
WARNING:
Remove fuel cap slowly to avoid injury from fuel
spray. Never operate the unit without the fuel cap securely in place.
_
WARNING:
DO NOT USE E85 FUEL iN THiS UNIT. It has
been proven that fuel containing greater than 15% ethanol will
likely damage this engine and void the warranty.
1.
Remove the fuel cap (Fig. 7).
2.
Place the gas container's
spout into the fill hole on the
fuel tank (Fig. 7) and fill the
tank.
NOTE:
Do not overfill the tank.
3.
Wipe up any gasoline that
may have spilled.
4.
Reinstall the fuel cap.
5.
Move the unit at least 30 ft.
(9.1 m) from the fueling
source and site before
starting the engine.
Gas Can Spout
Tank
Fig. 7
5
Publicidad
