Tru-Test 6 J Manual Del Usuario página 3

To install the energizer indoors:
1 Select a suitable installation site. See
installation on page 2.
2 Mount the energizer on a wall 1.7 m (5'6") above ground level.
Use the template printed on the back cover of this manual, if
required.
3 Connect the Fence earth terminal (green) to the energizer earth
system.
6000i, X6i and 406i:
4 If earth monitoring is desired, connect the
Fence earth monitor terminal (black) to a separate earth rod. For
Earth monitoring
more information, see
5 Connect the Fence full voltage terminal (red) or the Fence half
voltage terminal (yellow) to the fence.
6 Connect the energizer to mains/line power using the mains/line
power adaptor provided. See
leads
on page 2.
Note:
For information about using the Fence half voltage terminal for a
bi-polar fence installation, see Bi-polar installation
information about using the Fence half voltage terminal to reduce the
Reducing the fence voltage output
fence voltage output, see
Note:
If the energizer is being installed indoors, it may be powered by
a battery instead of mains/line power, if required.
Warning!
If using a battery to power an energizer that is installed
indoors, ensure that there is adequate ventilation to allow battery
gases to disperse.
Installing the energizer outdoors
The energizer may be installed outdoors, powered by a battery.
Warning!
USA/Canada - Refer to
Class 2 power units (USA/Canada only)
countries - Do not power the energizer with mains/line power if it is
being installed outdoors.
To install the energizer outdoors:
1 Select a suitable installation site. See
installation
on page 2.
2 Mount the energizer on a post. Use the template printed on the
back cover of this manual, if required.
3 Connect the Fence earth terminal (green) to the energizer earth
system.
4 6000i, X6i and 406i: If earth monitoring is desired, connect the
Fence earth monitor terminal (black) to a separate earth rod. For
more information, see Earth monitoring
5 Connect the Fence full voltage terminal (red) or the Fence half
voltage terminal (yellow) to the fence.
Selecting a site for the
on page 4.
Using the power adaptor and battery
on page 7. For
on page 7.
Important safety instructions for
on page 10. All other
Selecting a site for the
on page 4.
6 Connect the energizer to the battery using the battery leads
Using the power adaptor and battery leads
provided. See
page 2.
Note:
For information about using the Fence half voltage terminal for a
Bi-polar installation
bi-polar fence installation, see
information about using the Fence half voltage terminal to reduce the
Reducing the fence voltage output
fence voltage output, see
Installing the energizer as part of a solar installation
The energizer may be installed with solar panels as part of a solar
installation.
A solar installation consists of these items:
The energizer
•
A battery (or battery bank)
•
One or more solar panels
•
An energizer earth system.
•
For information about the type of batteries to use for a solar
Battery selection for a solar installation
installation, see
The required power rating of the solar panel(s) depends upon the local
conditions. For help with positioning your solar panel correctly, see the
supplier of your solar panel and refer to your local meteorological
service. For more information about solar installations, refer to
www.tru-test.com.
Warning!
Do not power the energizer with mains/line power if it is
being installed outdoors. USA/Canada - Refer to
instructions for Class 2 power units (USA/Canada only)
To install the energizer as part of a solar installation:
1 Select a suitable installation site. See
installation
on page 2. For solar installations, it is also important
to select a site where the solar panel(s) will not be subject to
shading from the sun at any time.
2 Face the solar panel towards true north in the southern
hemisphere and true south in the northern hemisphere.
3 Tilt the panel so that it faces directly on to the mid-winter midday
sun. If necessary, to increase efficiency, adjust the tilt angle at
different times of the year.
4 When the solar panel is positioned correctly, attach the energizer
to the rear of the panel. Alternatively, mount the energizer on a
fence post. Use the template printed on the back cover of this
manual, if required.
5 Connect the Fence earth terminal (green) to the energizer earth
system.
6000i, X6i and 406i:
6 If earth monitoring is desired, connect the
Fence earth monitor terminal (black) to a separate earth rod. For
Earth monitoring
more information, see
7 Connect the Fence full voltage terminal (red) or the Fence half
voltage terminal (yellow) to the fence.
8 Connect the battery to the solar panel.
9 Connect the energizer to the battery using the battery leads
provided, but replace the battery lead clips with permanent
on
on page 7. For
on page 7.
on page 6.
Important safety
on page 10.
Selecting a site for the
on page 4.
3