Tabla de contenido
Publicidad
REMARK
-
MAKE SURE THE DIRECTION IS CORRECT WHEN INSERTING THE TAPE INTO THE SYSTEM.
-
THERE IS SOME SEARCHING NOISE CAN BE HEARD AND THE SYSTEM CANNOT PERFORM NORMAL
PLAYBACK FUNCTION DURING FAST FORWARD MODE.
-
THIS IS RECOMMENDED TO TAKE OUT THE CASSETTE TAPE FROM THE SYSTEM EVERY TIMES AFTER
LISTENING AND DON'T LEAVE THE CASSETTE TAPE INSIDE THE SYSTEM WHEN NOT UNDER
PLAYBACK MODE.
PHONO
NOTED:
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
-
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1.
SELECT TO " PHON/AUX " FUNCTION FROM FUNCTION SELECTOR (19)
2.
SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3.
PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4.
LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE.
THE PLATTER WILL START TO ROTATE.
5.
PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6.
ADJUST THE VOLUME TO THE DESIRED LEVEL.
7.
AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT
THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
8.
TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST TRACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (30) TO " OFF
" POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO " ON " POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
MORE FEATURES
A. SLEEP SETTING (BY REMOTE CONTROL)
1. PRESS "SLEEP" BUTTON AND SLEEP INDICATOR "
2. KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90 > 75 >60....15
MINUTES.
3. SYSTEM WILL STOP AND GOTO STANDBY MODE AUTOMATICALLY AFTER THE SELECTED TIMING.
4. TO CANCEL THE SLEEP MODE, PRESS " SLEEP " BUTTON UNIT IT REACHS "OFF" MODE.
REMARK:-
IF PRESS THE SLEEP BUTTON ONCE AND THE SLEEP INDICATOR "
(21), THE SYSTEM WILL GOTO STANDBY MODE AUTOMATICALLY AFTER SELECTED MINUTES.
B. ALARM CLOCK SETTING (BY REMOTE CONTROL)
THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY CD, TUNER,
USB OR SD MODE RESPECTIVELY.
FIRST, SET THE UNIT AT STANDBY MODE AND THEN PRESS & HOLD THE " TIMER " BUTTON TO ENTER THE
SETTING MODE, THE LCD DISPLAY WILL SHOW SET TIME – SELECT SOURCE :-
1) WAKE UP SOURCE : PRESS THE " FUNCTION " BUTTON TO SELECT THE SOURCE FORM " TUNER FM " –
" TUNER MW " - " USB
AGAIN AFTER SELECTED THE SOURCE.
2) WAKE UP TIME : PRESS
PRESS " TIMER " BUTTON " TO STORE THE MEMORY.
SKIP UP
/ DOWN
MCD1700 / English instruction manual
" WILL SHOWN ON THE LCD DISPLAY (21).
" - " SD
" – CD REPEATLY. PRESS " TIMER " BUTTON
" BUTTON
TO SET THE HOUR & MINUTES AND
ENG 10
" APPEAR ON THE LCD DISPLAY
Publicidad
Tabla de contenido
