Setup Instructions - Belkin TuneCast II Guia Del Usuario

Setup Instructions

Please ensure that you are not driving when setting up or operating the TuneCast 2.
1. Open the battery cover on your TuneCast II Mobile FM Transmitter. Install the included AAA batteries and
replace the battery cover.
2. Plug the 3.5mm connector into your iPod player or other portable music device.
3. The AUTO ON feature will power on the FM Transmitter when the unit detects an input signal. Your FM
Transmitter's "AUTO ON/OFF" feature uses your audio player's volume level to automatically power
on and off. For best results, keep your player set at a medium volume level. NOTE: Setting your device
volume very low may cause the FM Transmitter to turn off, even if the audio player is on. You can also
press and hold both and buttons simultaneously for two seconds to turn on the unit. To turn off the
unit, press and hold both buttons simultaneously again for two seconds.
Note: To conserve power, the FM Transmitter will automatically turn off when there is no input audio signal for
60 seconds +/- 10 seconds.
4. Tune your car or home stereo frequency to a channel with a weak broadcast signal. The ideal channel is
one that is not broadcasting a radio program, or is doing so weakly.
5. Press the or button on the FM Transmitter to select the transmission frequency chosen in step 4, on
your car or home stereo, for broadcast. Press and hold either button for fast-forward or backward tuning.
6. To memorize a specific frequency (four stations maximum) for easy selection:
a. Select the desired frequency using the or
b. Press and hold "mem" (memory) button for two seconds. The icon M1 will blink; then release it.
c. Press the or button to select one of the memory slots M1, M2, M3 or M4 for storage. The active
memory slot icon will blink.
d. Press the "mem" button again to store the frequency and return to normal operation mode.
e. In operation mode, pressing the "mem" button will toggle among the four memory slots to retrieve the
memorized frequency.
NOTE: When there is no key press for a duration of 10 seconds, the FM Transmitter will return from memory
mode to operation mode.
7. Adjust the volume on your MP3 player or other audio source to a medium level.
8. Adjust the volume of your FM radio to the desired listening level.*
Mobile Power Cord Included for Extra Power
Connect one end of the cable into the DC port located on the bottom of the FM Transmitter.
Plug the other end of the cable into the cigarette lighter port in your car
Once the cable is plugged into the FM Transmitter, the unit will shut off. You will need to manually turn on the unit.
NOTE: This cable will NOT charge the TuneCast II Mobile FM Transmitter. It only provides power in order to
preserve battery life while in the car.
For best results:
• Try to keep the FM Transmitter close to the antenna of your FM radio. While the FM Transmitter often
works at distances of 30 feet or more, a distance of 10 feet or less will minimize interference and provide
the strongest signal.
• Keep fresh batteries in the FM Transmitter. When the batteries become very low, the transmission strength
will weaken.
*Due to characteristics of FM transmission, you will experience better sound quality by adjusting the volume
on your home or car stereo when necessary, and by leaving your iPod or other portable music player volume
at a medium level.
P74456_B_F8V3080_Man.indb 3
buttons.
Information
Warning
Do not insert any objects other than the cigarette lighter adapter into the power outlet without
disconnecting the battery of the vehicle first. Failure to observe this safety warning can result
in injury or property damage.
Belkin does not assume any responsibility for personal injury or property damage incurred due to
hazardous driving as a result of interaction with this device, the iPod, or the vehicle's power outlet.
Electrical/Environmental Specifications
CLA Power Requirement: 12V DC, 500mA at CLA input
Glass tube Fuse: Current rating 500mA
Under certain circumstances ESD may cause this device to shut down. In these circumstances
simply power the unit off by removing the CLA and then plug back in, restore power and switch
back on.
This device complies with the WEEE directive. For recycling information please follow the
following link: www.belkin.com/environmental
European Standards Compliance Statement
This device has been tested and found to be compliant with the requirements of the
R&TTE Directive. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This device generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If the TuneCast II does cause harmful interference to radio or television reception, which
can be determined by turning this device on and off, the user is encouraged to try to
correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between this device and the receiver.
• Connect this device into a power outlet on a circuit different to that which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TuneCast II is compliant to EN 301 357, EN 301 489, EN 60950 and EN 50371.
At 6 February 2008 this device may be used in: Germany, Switzerland, Iceland,
Lichtenstein, Poland, Estonia, Czech Republic, Norway, Finland, Luxembourg, Denmark,
Spain, Portugal, Sweden, United Kingdom, Bosnia and Herzegovina, Ireland and Belgium.
Please see national legislation or Recommendation 70-03 implementation table for
current position http://www.ero.dk
EN
0673
19/05/2008 17:08:25