Extraordinary Maintenance - Diamond MAV-65 Manual De Instruccion

BREAKS OR DAMAGES RESEARCH AND MOVING ELEMENTS UNBLOCKING
Here follow are indicate the interventions for the breaks or damages research and moving elements unblocking which can
be performed from maintenance men.
TYPE POTENTIAL/S CAUSE/S
General Blackout
Net voltage
Fuses or magneto thermals intervention
lacking
place upstream of the machine feeding
line
Protection device intervention inside
Functioning
the machine
intervention
Cause/s not identifiable
Feeding voltage lacking.
The machine
doesn't Sectioning devices set on "OFF".
function: the
blades don't Lacked running button functioning
rotate or don't
perform Thermal intervention due to the
correctly the overheating
cutting
Visualization on the display of the
letter "E"

EXTRAORDINARY MAINTENANCE

For the intervention of extraordinary maintenance, consequent to breaks or revisions or mechanical and electric damages, it
is necessary an intervention request directly to the Authorized Assistance Center.
The instructions about the extraordinary maintenance don't appear in the present instruction manual for the use and so
must be explicitly requested to the manufacturer.
CLEANING
It is forbidden to clean by hand the organs and the elements in motion.
All cleaning interventions must be started only and exclusively, after having unloaded the machine with the
food product in working and having insulated from the electric feeding source and from external energy.
The machine, the electric equipment and the machine board components must not be ever washed utilizing
water, and not in any kind of jets form and quantity; so, without "bucket" nor "rubber" nor "towel".
Don't put ever directly the machine in the sink or under the tap.
The machine hygiene level classification and the associated equipment, for the foreseen use, are 2 (two): machine that,
after a hygiene risk evaluation, is in conformance with applicable international standards requirements, but requests a
programmed disassembly for the cleaning.
FREQUENCY PERSONNEL
At the end of every
shift work and
however before the
daily use
Contact the electric energy distributor
After having eliminated the causes that have determined the protection device
intervention, restore it. In case of problem persistency contact an electrician
technician.
Contact an electrician technician: after having eliminated the causes that have
determined the protection device intervention, restore it.
Contact directly the Authorized Assistance Center
Check and restore the electric energy
Connect the plug on the feeding socket
Check the button efficiency and eventually contact directly the Authorized
Assistance Center.
Wait the complete cooling before to machine restarting
Speed reader damaged, contact directly the Authorized Assistance Center
Operator All the surface and the machine parts destined to come in contact with the food product or with
the food zones (tools external and internal surface) and the jets zones (tool superior surface
connected with the machine and machine external surface), must be cleaned and disinfected
with the under reported modalities. For the grinding group disassembly activities see the
previous descriptions.
Scrape the surfaces from the possible food product residuals (for example with plastic
scrapers);
Clean all the food zone surfaces and jets zone with a morbid dampened clothes (not
draining) with detergent diluted in hot water (also common soap for dishes is good).
Don't soak them. With a towel clean inside the grinding mouth. Use specific products for
steel, which must be liquids (not in cream or pastries however abrasive) and above all must
not contain chlorine. Against the fat substances the denatured alcohol.
Rinse with cleaned hot water and successively dry all food zone surfaces and jets zone
with soft clothes that don't lose coats.
The mixer tool, being in stainless steel, cannot be washed in dishwasher, much less the
plastic parts.
The reassembly must happen only following working requirements, leave the pieces
wrapped up in soft dry clothes that don't lose coats.
PERIODS OF LONG INACTIVITY
During the machine long inactivity periods provide to pass vigorously on all steel surfaces
(especially if stainless) a clothes soaked of Vaseline oil so that to spread a protective veil.
THINGS NOT TO DO BEFORE OR DURING THE CLEANING:
Enter towards the moving elements without to be previously checked of their stop;
Enter towards the moving elements without have stopped it in safety stop (blockage in zero
position of the electric feeding sectioning devices)
MODALITY AND COMPARISON
MODALITY
Pag. di
12 13