How To Listen To The Fm Radio; How To Use The Wired Audio Input - Midland BT Next Manual Del Usuario

by the GPS itself.
Pairing to a PMR446 radio with integrated or external Bluetooth
The PMR446 Radio must be paired to the "Volume –" button, so if the
"Background" feature is activated, the PMR446 radio is always in the background
even when you talk on the intercom.
Attention: in addition to a PMR446 transceiver, if you want to connect also a GPS
navigator you must pair the GPS to the "Volume +" button. In this configuration the
GPS street voice announcements will interrupt all other communication (Intercom,
FM Radio, Music).
When the GPS is paired to the "Volume +" button the "Phone" mode is activated.
How to pair PMR446 transceiver with integrated Bluetooth
If your PMR446 trasceiver has an integrated Bluetooth (like the G8BT), you must pair
the trasceiver using the "Volume –" button:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on
permanently.
› Now press firmly (3 sec) the "Volume -" button, the Blue and Red light will flash.
› Follow now the pairing procedure explained on the manual of the transceiver
itself
Attention: If you are pairing to a G8BT transceiver, just when the BT Next C. finish the
pairing (only the Blu LED is flashing) you must follow this procedure to activate the
Bluetooth connection:
› Turn off and on the G8BT and then press for 3 sec. the "BT" button.
› Go to phone mode
› Press "Backward" button to activate G8BT audio (no need to make the pairing
procedure again)
You need to have "background" feature active if you want to have the two way radio
conversation in background with the intercom

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the "FM
Radio" mode in order to use it. Long press the middle button until you hear "FM radio"
from the voice announcement. Now all the three main buttons are dedicated to the FM
C-Radio FM mode
Mode Forward button
FM Radio Short press: seek station up
Long press: Scan recorded
28 - Midland BT Next
Radio (See Table C).
Press short the Forward or the Backward button to seek the FM Radio station. When
you press long the Forward or the Backward button, you can scan up or down the 6
recorded stations. A voice announcement will tell you the number of which memory
you are entering. A double beep tone will be played when the last or the first recor-
ded station is reached.
To save the station you are listening to, press the Forward and Rear buttons together
for 3 sec. You will hear a beep tone for confirmation.
The station is saved over the last recorded station used.
Thanks to the RDS system, the FM Radio will choose the strongest signal available for
the radio station you like to listen.
The RDS system is OFF by default, if needed you can toggle on/off the RDS pressing
together the "Volume +" and "Volume –" buttons for 3 sec when the radio is on. A
voice announcement will tell you the RDS status.
How to Disable/Enable the FM Radio
By default the FM radio is on.
Disabling:
› Enter the "Setup" mode: turn off the unit and hold down the "Middle" button
about 7 sec., until the Red light is on permanently.
› Press "Middle" and "Volume+" buttons together for 3 seconds. The blue LED will
flash twice.
› Double click on the "Middle" button to exit the "Setup" mode and use the BT NEXT C.
Enabling:
› Follow the same procedure up described; now the blue LED will flash once.
To exit the "Setup" mode, double click the "Middle" button.
FM Radio with intercom
When you are in "FM Radio" mode is not possible to manually open the intercom,
you can only open it using VOX feature (just talk) to the unit paired on the "Middle"
button. To manually activate the intercom you must switch to "Intercom" mode.

How to use the wired audio input

Your Midland BT Next C. is also supplied with a wired audio input (AUX), that can be
used to connect an audio source, like an iPod (or any other MP3 Player) or a PMR446
Middle button
Short press: On/off
Long press: Change mode
Rear button
Short press: seek station up
Long press: Scan recorded