Before Starting The Equipment - EINHELL ERGOTOOLS E-PST 800 L Manual De Instrucciones

Sierra de vaivén electrónica
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 17
Anleitung E-PST 800 L_SPK7:_
GB
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L
sound pressure level
90,3 dB(A)
pA
K
uncertainty
pA
L
sound power level
101,3 dB(A)
WA
K
uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 60745.
1. Sawing wood
Vibration emission value a
= 6.591 m/s
2
h
K uncertainty = 1,5 m/s
2
2. Sawing sheet metal
Vibration emission value a
= 5.204 m/s
2
h
K uncertainty = 1,5 m/s
2
Important!
The vibration value changes according to the area of
application of the electric tool and may exceed the
specified value in exceptional circumstances.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Safety guard (Fig. 2-3/Item 15)
The safety guard (15) protects the user from
accidentally touching the saw blade (12) and
nevertheless enables you a free view of the
cutting area.
The safety guard (15) must always be fitted when
carrying out cutting work.
To remove the safety guard (15), release the two
safety guard holders from the recesses in the
guide by applying slight pressure to the bottom
edge of the guard. Then pull the safety guard
forwards along the guide (see Figure 3).
14
28.04.2008
16:15 Uhr
5.2 Changing the saw blade (Figs. 4-5/Item 12)
Important!
You can fit or replace saw blades without using
any other tools.
Pull the mains plug before you fit or replace a saw
blade.
Set the selector switch for pendulum action (8) to
3 dB
position 3.
The teeth of the saw blade are very sharp!
Remove the safety guard (15) (see point 5.1).
3 dB
Press the rotary lock on the saw blade holder
(14) as shown in Figure 4 and guide the saw
blade (12) into the saw blade holder (14) as far
as it will go. The teeth on the saw blade must be
pointing forwards.
Allow the rotary lock on the saw blade holder
(14) to slide back into position. The saw blade
(12) must sit in the guide roller (10) (Figure 5).
Check that the saw blade (12) is securely
mounted in the blade holder.
Follow the instructions above in reverse order to
remove the saw blade.
5.3 Installing the parallel stop (Figure 6/Item 11)
The parallel stop (11) enables you to saw parallel
cuts.
Undo the two locking screws (13) on the
soleplate (7).
Now slide the parallel stop (11) into the guides on
the soleplate (7). You can fit the parallel stop (11)
on either the left or right of the equipment.
The guide strip must always face downwards. Set
the required distance using the measurement
scale on the parallel stop (11) and tighten the
locking screws (13) again.
5.4 Setting the soleplate for miter cuts (Figs. 7-8)
Use the Allen key (4) to loosen the screws for the
soleplate (18) on the bottom of the adjustable
soleplate (7) (Figure 7).
Pull the sole plate (7) backwards slightly. The
soleplate can now be swiveled a maximum 45°
to the left and right.
If the soleplate (7) is pushed back to the rear
again, it will only function in the locking positions
at 0°, 15°, 30° and 45°, which are marked on the
graduated scale for the soleplate (9) (Figure 8).
Move the soleplate into the required position and
refasten the screw securing the soleplate (18).
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate (7)
to the rear, set the desired angle and refasten
the screw securing the soleplate (18).
Seite 14

Publicidad

Tabla de contenido
loading

Productos relacionados para EINHELL ERGOTOOLS E-PST 800 L

Este manual también es adecuado para:

43.210.91

Tabla de contenido