Página 1
TELEVISOR A COLOR Chassis : KS7D(N)_Prime-2 Model : CL29Z50MQTXXAO MANUAL Servicio TELEVISOR A COLOR CARACTERÍSTICAS GREEN CRT ■ ■ ■ Turbo Voice CL-29Z50MQ Referirse al manual de servicio en GSPN (véase página siguiente) para más información.
Comprobar el cable de cias. Cuando el voltaje exceda los límites especificados, alimentación AC en busca de daños. Mantener partes o compruebe cada pieza especial. conductores lejos de cualquier material emisor de calor. Samsung Electronics...
Página 6
Las partes críticas de seguridad deben soportar-( se usando sólo las piezas habituales para los reempla- zos (particularmente, resistencia a la llama y especifica- ciones de intensidad dieléctrica). Las partes o materiales inhabituales pueden causar descarga eléctrica o fuego. Samsung Electronics...
ON. Conecte medidor de resistencia (500 V) a las láminas del enchufe de AC. La resistencia del aislamiento entre la lámina del enchufe AC y las partes conductoras accesibles debe ser más de 1 ㏁. Samsung Electronics...
Para reducir el riesgo de descarga eléctrica no realizar ningún manteni- miento sin tener en cuenta el contenido de instrucciones de operación a menos que usted esté calificado que sea así. Samsung Electronics...
5. Cercíorece de apagar y desenchufar el cable eléctrico del toma antes de reubicar el producto. También com- pruebe que el cable de la antena o conectores externos si están completamente desenchufadas. El daño en el cable pueden causar incendio o descarga eléctrica. Samsung Electronics...
- VCT4822_F1: Procesador de Sonido, Procesador de Video, Controlador del Procesador de Display y Deflection, OSD y Procesado de Texto - TDA7297SA : Amplifica la Señal de Sonido - STR-X6750F: Suministro de Energía HIC - TDQ-6F/13F2S (Tuner): Procesamiento de señal RF, salida de señal IF - TECCIO4OSL32A(E) : Tuner Principal PIP-2Tuner - TMQH2-003A,2 Tuner Secundario PIP-tuner Samsung Electronics...
Product Specification 2-2 Características Principales Modelo CL-29Z50MQ Voltaje AC100-240 V(Mejico : AC127V) Frecuencia de Operación 50/60 Hz Consumo de Energía 140 Watts 36.7 x 15.9 x 22.3 inches Dimensiones (mm/pulgadas) 934 x 406 x 568 mm Peso (Kg/ lbs) 54.5 kg / 120.1 Ibs ■...
Product Specification 2-3 Análisis de Especificaciones Model CL29M6PQ CL-29Z50MQ Chassis KS7A KS7D Design Screen Size 29" 29" FLAT SLIM-FIT DNIe Jr. ■ Comb Filter Velocity Modulation Picture Video Noise Reduction Auto Kinetic Bias Color Tone Control Tilt Control Picture Mode...
2. Cuando reemplace la Main Board : Se requieren estos ajustes: Focus, voltaje de pantalla y W/B. 3. Cuando reemplace el Ensamble CRT : No se requieren ajustes. 4. Cuando reemplace el Side AV : No se requieren ajustes. Samsung Electronics...
Página 16
RESET G2 ADJUST 3. Funciones de los botones dentro del Modo de Servicio. Muestra todos los menús MENU Mover el cursor para seleccionar un item. ▲ / ▼ Ajusta el valor de la configuración seleccionada ◀ / ▶ Samsung Electronics...
CL-29Z30MQ V Amp V Shift H EW H Shift V Linearity V SC H Parabola Upper Corner Lower Corner Upper Corner6 Lower Corner6 H Trapezium Angle EHT Time EHT Threshold EHT Vertical EHT Horizontal EHT Vertical2 EHT Horizontal2 Samsung Electronics...
Página 18
CL-29Z30MQ V Amp V Shift H EW H Shift V Linearity V SC H Parabola Upper Corner Lower Corner Upper Corner6 Lower Corner6 H Trapezium Angle EHT Time EHT Threshold EHT Vertical EHT Horizontal EHT Vertical2 EHT Horizontal2 Samsung Electronics...
Página 20
CL-29Z30MQ R Cutoff G Cutoff B Cutoff R Drive G Drive B Drive Sub Bright Sub Contrast Sub Color Sub Tint AKB Option BCL Threshold BCL Gain BCL Time Sub Sharpness Pilot Low Pilot High V-Mute(x100ms) BCL TCUP Samsung Electronics...
Página 21
Item Remark CL-29Z30PQ CL-29Z30MQ Melody Volume HB Start HB Stop RF AGC VM Gain VM Delay V Peaking BLE Tilt BLE Gain BLE Mode BLE Break CTI Gain CTI Coring LTI Gain D-EHT Time DCT Ratio VSP COMB Samsung Electronics...
Página 22
PIP NTSC V.Pos PIP H.Pos PIP R Cutoff PIP B Cutoff PIP R Drive PIP B Drive 6. YC Delay 29" SLIM 29" SLIM Item Remark CL-29Z30PQ CL-29Z30MQ PAL Delay SECAM Delay NTSC Delay PAL(AV) Delay SECAM(AV) Delay NTSC(AV) Delay Samsung Electronics...
Página 24
TTX V Position TTX H Position TTX Contrast TTX Brightness OSD Contrast OSD Brightness Double TTX H Position Standard Equ100(Std BASS) Standard Equ300(Std TREBLE) Standard Equ1K(Music BASS) Standard Equ3K(Music TREBLE) Standard 10K(Movie BASS) Music Equ100(Movie TREBLE) Music Equ300(Speech BASS) 3-10 Samsung Electronics...
Página 25
PIP G CUTOFF PIP G DRIVE OSD/PIP BRIGHT BALANCE PIP BRIGHT OFFSET MDB_STRENGTH MDB_HARMONIC MDB_HP MDB_LP MDB_LIM MDB_CUTOFF EHT POSITION 1 EHT POSITION 2 3.4CH SLLTHD (TV-NO NOISE) CH SLLTHD (TV-NO NOISE) LNA Operating Point SLLTHDV(TV NO NOISE) Samsung Electronics 3-11...
Página 26
Remark CL-29Z30PQ CL-29Z30MQ LNA Default LNA SWITCH LMIXOFS H-OUTDEL CR-P Initial CR-I Initial DRX_CR_AMP_TH Over Modulation Return Counter VCR Mode Counter "VID_AMP_HEAD_BS(In the modula- tion)" CR_P (In the Over Modulation) "THRSEL(picture shaking when weak signal)" SLLTHDVP EEP_BC_MIN_LIMIT 3-12 Samsung Electronics...
Página 27
2RCA+S+DVD 2RCA+S+DVD Tilt Vchip Caption 2-Tuner Auto On StandBy LED Philippines(AV MULTI) Osd Language English English FM Radio Antenna Disp Hi-Deviation Plug & Play DNIe Jr Volume Curve Small Small Color Matrix Japan Japan PWM/Parabola Parabola Parabola Samsung Electronics 3-13...
② Presionar "Apagar → Mute → 1 → 8 → 2 → Encender" usando el control remoto e ingrese al Modo Fábrica. ③ Ingrese al Modo Deflection. ④ Ajuste items V-AMP, V-SHIFT, H-AMP y H-SHIFT de modo que el anchura sea 5 y el altura 4. Samsung Electronics 3-15...
Upper Coner 4 V-Linearity Low Coner 5 V SC ⑦ Al finalizar los ajustes, exhibir el patrón Lion y verificar que el tamaño de la imagen no ha cambiado. Si no hay cambio, finalice los ajustes. 3-16 Samsung Electronics...
1. Exhibir el patrón Cross Hatch. 2. Gire el Focus a la derecha para optimizar la posición. 3. Gire lentamente Focus a la derecha de modo que la línea cruzada sea vea lo más claro posible. Después del Ajuste Focus Samsung Electronics 3-17...
1. "Apagar → Mute → 1 → 8 → 2 → Encender" para ingresar al Modo Servicio. 2. Aplicar el patrón Toshiba. Screen 3. Use control remoro para ir al modo "G2 Adjust" manualmente. 4. Gire VR Screen en FBT y confirme que los caracteres de abajo cambien de Rojo a Verde. 3-18 Samsung Electronics...
4. Cuando finalice el ajuste, comprobar los siguientes puntos. - Si hay un punto en la pantalla al apagar/encender el TV, ajuste el Voltaje de Pantalla nuevamente. - Si hay una línea fantasma en la pantalla, ajuste el Voltaje de Pantalla nuevamente. Samsung Electronics 3-19...
Página 50
2) Check that the Tact Switch has been pressed. 3) Check that the signal cable is properly connected. 4) Check that channel setting has been set. ■ When the picture is abnormally displayed on the screen, display the Test pattern and check the adjustment status. Samsung Electronics...
Página 51
When the screen is not properly displayed and the left or right side of the picture is shrunk, or the top or bottom of the screen is expanded or shrunk, check if the Deflection Blcok is out of order. Samsung Electronics...
Página 52
If you press the power switch of the or the channel key on the remote control when in St-BY sta- tus, the screen will be turned on. ○→◑ If the LED blinks and the screen is not displayed, check the connection between the Power and the Main Board. Samsung Electronics...
IC602 Problem → Change ICV201 Problem → Change 4. Fly Back Lion Badness Video B+ Check (IC501 6PIN) IC501 Check : 180V~210V ICV201 Problem → Change FD801S IC804 IC801S IC601 FP801S Power cord IC901 ICT501 IC201S T401 TU01S IC301S QE01 Q401 Samsung Electronics...
Página 55
The RF / CTV signal is transmitted to the Tuner of the Main Board. If the signal is not received, check the following items. - Power supply: 5V, 33V - Check for RF defects: Check the IF output - Check for AUDIO defect: Check the SIF Signal output Samsung Electronics...
Página 56
Troubleshooting 2. Micom Diagnosis VSP/MSP/DRX Block ETC - Power supply: 3.3V, 5V, 8V - Check for input defects: Y/C(CVBS, S-VHS), 480i Y/Pb/Pr signal Samsung Electronics...
Página 57
The signals are sent to VCTI and the selected signals are output. If the signal input or output does not work, check the following items. - Check for input defects: Check the Micom input pin. - Check for output defects: Check JAR701 (for RF/AV) or JA701(for comp/S_VHS) Samsung Electronics...
Página 58
This receives the signal from the Audio Processor (VCTI) and outputs the signal in7W+7W / 10W + 10W sound. - Power supply : 14V - Check for input defects : AMP-R,AMP-L - Check for output defects : L+, L-, R+,R- Samsung Electronics...
Página 59
If the voltage is measured, the problem is a defect in the FBT unit. (When you don't have an oscilloscope, and you can hear the high-voltage sound, you can determine that the horizontal TR is normal.) - Is the vertical input waveform output from the VCTI VDP Pin. 6-10 Samsung Electronics...
* CNV901A : This is a 6P connected from Tact,S/W pcb for IR,LED,5V. * CN902 : This is a 4P connected from Control PCB for Key1,Key2 input signal. * CN601 : This is a 4P connected to Speaker for Sound output signal. Samsung Electronics...
Página 65
Connected to the CRT Ass'y PIN No. Pin Name PIN No. Pin Name TILT CN503B CN701 Connecte to the CRT Ass'y Connected to the Side AV Port PIN No. Pin Name PIN No. Pin Name -16.5V +16.5V HEATER 200V Samsung Electronics...
Página 66
This supplies the final R/G/B signal from the Main Board and the CRT deflection signal to the CRT. 9-2-2 Names & Roles of Key Parts * CN503 : This is a 14P connected from MAIN PCB for R/G/B/AKB/HEATER/B+200V. * GT501,GT502 : This is a 2P connected to TBC-WIRE. Samsung Electronics...
Página 67
PCB Diagram 9-2-3 CRT Board Connector Pin CN503 Connects the R/G/B signal and power for the CRT and AMP from the Main Board. PIN No. Pin NAME TILT -16.5 +16.5 Heater +200V Samsung Electronics...
Página 68
Schematic Diagram 10. Diagramas Esquemáticos 10-1 MAIN This Document can not be used without Samsung’s authorization. Power TP07 Signal TP09 TP08 TP09 TP07 TP08 Samsung Electronics 10-1...
Página 69
Schematic Diagram 10-2 POWER This Document can not be used without Samsung’s authorization. TP01 Power TP01 Signal TP02 TP04 TP02 TP04 TP05 TP06 TP06 TP05 10-2 Samsung Electronics...
Página 70
Schematic Diagram 10-3 Sound This Document can not be used without Samsung’s authorization. Samsung Electronics 10-3...
ENTER button on the remote control. features. + VOL – Press to increase or decrease the volume. In the on-screen menu, use the + VOL – button as you would use the œ œ and √ √ button on the remote control. Samsung Electronics 11-1...
Página 72
Use the left side panel jacks to connect a component that is used only occasionally, such as a camcorder or video game. S-VIDEO Video inputs for external devices with an S-Video output. AV IN 2 Video and audio inputs for external devices. 11-2 Samsung Electronics...
Página 73
DVD or DTV set-top box. 480i video signal input is available. AV OUT Connect to the audio/video input jacks of a recording ANT IN VCR. Connect to an antenna or cable TV system. Samsung Electronics 11-3...
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote control, always point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box. 11-4 Samsung Electronics...
Página 75
② Tap the upper part of the Back Cover 2 or 3 times and pull the Back Cover to separate it from the unit. : Disassemble the product after disconnecting the power cord and discharge the unit to prevent an electric shock and damage to the product due to static electricity. Samsung Electronics 12-1...
Página 76
① Separate the Side AV Wire from the Front Cabinet and the Main Board. ② Pull Holder Chassis like the picture arrowdirection. ① Separate the Control 4P Wire,6P Wire,Speaker Wire from the Front Cabinet and the Main Board. 12-2 Samsung Electronics...
Página 77
Disassembly & Reassembly Part Name Description Description Photo Chassis ① Separate the Power cord,D-COIL,TILT,DY connector from Holder Main Board ① Remove the screw. Samsung Electronics 12-3...
: Take care when separating the wires because pulling the wires by force may damage the socket. In addition, separate the wires on a flat and clean surface so as to prevent scratching of the material and the PCB. 12-4 Samsung Electronics...
Página 79
Disassembly & Reassembly 12-1-4 Disassembling the Main Board Part Name Description Description Photo Main Board ① Separate the cable from the Main Board. ① Separate the cable from the Main Board. Samsung Electronics 12-5...
* Micom Block consists of five aspects as: Video & Sound IF Processor,Sound Processor, Video Processor, Display and Deflection Processor and Controller, OSD,Text Processing. * TDQ-6F/13F2S (Tuner): RF signal processing, output IF signal. Samsung Electronics 13-1...
* EEPROM: As a extended ROM of TVT. It contains some data which is used to program executing. * STR W6750F: SMPS control HIC. Provide switching signal in order to control the trans working. * TDQ-6F/13F2S(TUNER): Receives the RF signal and output a fixed IF to Micom. 13-2 Samsung Electronics...
Audio Multimix Audio Multimix provee 2 idiomas para el audio en la emisión extranjera de película, teatro, noticias, etc. Puede seleccionar y escuchar uno de los idiomas soportados o puede seleccio- nar y escuchar ambos idiomas simultaneamente. 14-2 Samsung Electronics...