Sammic SAM-3001 Manual De Instrucciones página 7

- As the motor starts, an ascending whirl
develops inside the tub, causing the items of
cutlery to circulate.
- The UV-c lamp lights up.
- The temperature control switches on so that
the granules reach the necessary temperature
for drying and polishing the cutlery.
- In the SAM-3001 and SAS-6001 models, the
fan starts along with the motor, which prevents
dirt and polish coming out with the pieces of
cutlery
- If you press stop (B) or open the top cover, the
machine stops. In the SAS-6001 mode, the
motor brake is activated.
- Disconnect the power supply using the
general switch (G).
Cutlery temperature control and drying
- If the polish granules are cold, the heaters are
connected and the light indicator 2 switches on.
Once the set temperature is reached, the heater
and the light indicator 2 switch off. The machine
ready light indicator 1 switches on and a
continuous beeping noise is heard which means
that you can start feeding cutlery in the cutlery
inlet (C). The dry cutlery will come out through
the front outlet (D).
- It is essential that the cutlery is wet or
directly coming from the dishwasher, i.e.
always damp, when loaded in the dryer
polisher.
- The polish granules cool down and at some
point the heaters reconnect and light indicator
2 switches on. You will see that the machine
ready light indicators 1 and the heaters 2 are
switched on. While the machine ready light
indicator 1 is switched on, continue to insert
cutlery.
- If there are too many polish granules, use cold
water. The granule temperature continues to
drop, the machine ready light indicator switches
off and an intermittent beeping noise is heard.
This means that the polish granules need to be
reheated. Stop feeding cutlery and wait until the
light indicator 1 switches on again and the
continuous beeping noise is heard.
Final polish granule drying cycle
With the machine stopped and the cover open,
by keeping the on switch (A) button pressed
down the light indicator 4 switches on and the
drying cycle is selected.
Lower the cover and start the cycle by pressing
the on switch button (A) again. The machine
starts and the granules are heated up to the set
temperature.
Wait for a few minutes with the machine on and
this will stop automatically, ending the cycle.
Run this cycle when you think that the polish
granules are damp or the machine has
undergone intensive use.
You should not use this cycle with dry granules.
To stop the cycle, just press stop (B) or open the
door.
Change of granule
Due to use and the presence of water and heat,
the effectiveness of the granules is reduced.
When the light indicator 3 is switched on, the
polish granules need to be changed. The light
indicator switches on after 200 hours.
To change the granules, remove used polish
granules using a vacuum cleaner. Then pour
the amount of polish granules supplied by
Sammic into the hopper through the central
cutlery feeding hole.
To reset the warning, with the machine off and the
door open keep the stop switch button (B) pressed
down.
Change of UV-c lamp
Over time and with use the UV-c lamp efficiency
is reduced. When the light indicator 3 blinks, it
means that the UV-c lamp needs to be
changed. The light indicator starts to blink after
1000 hours.
To reset the warning, with the machine off and the
door open keep the stop switch button (B) pressed
down.
Setting the temperature
You need to access the electronic board and select
the temperature by turning the potentiometer. The
temperature range is printed on the board.
Performance
Machine throughput depends on the weight of
the items of cutlery and the feeding rate.
SAM-3001: 2000 to 2500 pieces / hour
SAS-5001: 3500 to 5000 pieces / hour
SAS-6001: 3500 to 5000 pieces / hour
Items of cutlery shall be fed gradually, taking
care that those previously introduced have
disappeared into the granules (from 5 to 10
pieces at a time).
Feeding rates
SAM-3001 6 pieces / every 10 seconds.
SAM-5001 14 pieces / every 10 seconds.
SAM-6001 14 pieces / every 10 seconds.
Check that the flow of items of cutlery coming
out through the outlet (B) is homogeneous and
continuous.
Sanitising
The SAMMIC cutlery polisher uses a UV-C
lamp (E) for sanitising both the cutlery and the
granules.
This lamp has been successfully tested and is
duly certified, so cutlery is sanitised. Exposure
to the radiation of this lamp is harmful to the
eyes and skin. SAMMIC has implemented all
the necessary precautionary measures; any
improper use of the lamp is the user's sole
responsibility.
Error code
When the light indicator 4, end of drying cycle is
blinking, it means that there is a machine
failure.
· Probe error : "Quick" blinking that means that
there is no "on" and "off" cycle. Check the
probe connections or change the probe.
· Overheating error: Slow blinking. There is a
problem with the heater relay or the electronic
board.
To reset the alarm, switch off the general
switch G.
You can measure the probe heater to check its
state.
To do so, disconnect the contact switches. The
reference values are :
25 ºC - 10 KΩ.
50 ºC - 4.1 KΩ.
EN 7