HERKULES H-NT 20 Inox Manual De Instrucciones Original página 15

Fitting the foam fi lter (Fig. 7/25)
For wet vacuuming, slip the supplied foam fi lter
(25) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig.3/24) already fi tted upon delivery is not
suitable for wet vacuuming.
Fitting the pleated fi lter (Fig. 8/24)
For dry-vacuuming, slip the pleated fi lter (Fig.
3/24) over the fi lter basket (Fig. 2/20). The pleated
fi lter (Fig. 3/24) is suitable for dry-vacuuming only.
5.3 Fitting the tank bag (Fig. 9)
Fit the dirt bag (Fig. 3/27) as shown in Figure 9.
5.4 Fitting the suction hose (Fig. 1-3/9)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3/15)
The air regulator (15) can be fi tted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infi nitely ad-
justed using the air regulator (15).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
5.5 Suction nozzles
Dual-purpose nozzle (Fig. 3)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Various attachments can be fi tted to the combi-
nation nozzle depending on what you sort of work
you wish to carry out:
Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
Anl_H_NT_20_Inox_SPK7.indb 15 Anl_H_NT_20_Inox_SPK7.indb 15
GB
6. Operation
6.1 ON/OFF switch (Fig. 1/7)
Switch position 0:
Switch position I:
Switch position AUTO:
6.2 Dry vacuuming
Use the pleated fi lter (24) for dry vacuuming (see
point 5.2). The dirt bag (27) can be fi tted in additi-
on when removing particularly stubborn dirt (see
point 5.3).
Always ensure that the fi lters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam fi lter (25) (see
point 5.2).
Check that the fi lter is securely fi tted at all times.
When wet vacuuming, the fl oating safety switch
(Fig. 2/21) closes when the maximum tank level
is reached. In doing so, the suction noise of the
equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Danger!
The wet and dry vacuum cleaner is not suitable
for the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam
fi lter.
6.4 Automatic mode (Fig. 1)
Connect the power cable on your electric tool to
the automatic socket-outlet (4) and connect the
suction hose (9) to the extractor connector on
your electric tool. Check that the connections are
secure and air-tight.
You can use the supplied electric tool adaptor
(Fig. 3/22) to connect the suction hose (9) to the
electric tool. To do so, fi t it between the suction
hose and the extractor port on the electric tool.
Set the switch (7) on the wet and dry vacuum
cleaner to position AUTO, automatic mode. The
moment you switch on the electric tool, the wet
and dry vacuum cleaner switches on as well.
When you switch off the electric tool, the wet and
dry vacuum cleaner switches off as well after a
pre-set delay.
- 15 -
Off
Normal operation
Automatic mode
19.02.2018 15:13:55 19.02.2018 15:13:55