Automatic Mode; Dry Vacuuming; Wet Vacuuming - HERKULES H-SA 50 Manual De Instrucciones Original

Anleitung_H_SA_50_SPK7:_
GB
To extend the suction hose (9) you can attach one or
more of the elements which make up the 2-part
suction tube (17) to the suction hose (9).
Air regulator (Fig. 3/29)
The air regulator (29) can be fitted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infinitely adjusted
using the air regulator (29).
5.5 Suction nozzles
Dual-purpose nozzle (Fig. 3/14)
The dual-purpose nozzle (14) is for vacuuming solids
and liquids over medium to large areas.
Various attachments can be fitted to the combination
nozzle depending on what you sort of work you wish
to carry out:

Wet vacuuming

Use the attachment for wet vacuuming (Fig. 3/26).
Vacuuming smooth flooring
Use the attachment for smooth floors (Fig. 3/27).
Vacuuming carpets
Use the attachment for carpets (Fig. 3/28).
Fit the appropriate attachment into the combination
nozzle (14) from underneath and secure it to the
combination nozzle (14) using the side lugs (fig. 15).
Ensure that the attachments are perfectly secure.
Crevice nozzle (Fig. 3/23)
The crevice nozzle (23) is designed for vacuuming
solids and liquids in corners, edges and other areas
that are difficult to access.
6. Operation
6.1 ON/OFF switch (Fig. 2/7)
Switch position 0: Off
Switch position I: Normal operation
Switch position II:

Automatic mode

6.2. Dry vacuuming

Use the pleated filter (24) for dry vacuuming (see
point 5.2). The tank bag (35) can also be fitted for
removal particular heavy dirt (see point 5.3).
Always ensure that the filters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam filter (25) (see point
5.2).
Check that the filter is securely fitted at all times.
12
24.03.2010 9:26 Uhr Seite 12
Water drain screw (Fig. 1/11)
To make the tank (10) easier to empty after wet
vacuuming, it is fitted with a water drain screw (11).
Open the water drain screw (11) by turning it anti-
clockwise and drain the liquid.
Important.
When wet vacuuming, the floating safety switch (21)
closes when the maximum tank level is reached. In
doing so, the suction noise of the equipment will
change and become louder.
Then switch off the equipment and empty the tank.
Important!
The wet and dry vacuum cleaner is not suitable for
the vacuuming of combustible liquids.
For wet vacuuming, use only the supplied foam filter.
6.4 Automatic mode
Connect the power cable on your electric tool to the
automatic socket-outlet (4) and connect the suction
hose (9) to the extractor connector on your electric
tool. Check that the connections are secure and air-
tight.
You can use the supplied electric tool adaptor (22) to
connect the suction hose (9) to the electric tool. To do
so, fit it between the suction hose and the extractor
port on the electric tool.
Set the switch (7) on the wet and dry vacuum cleaner
to position II, automatic mode. The moment you
switch on the electric tool, the wet and dry vacuum
cleaner switches on as well. When you switch off the
electric tool, the wet and dry vacuum cleaner
switches off as well after a pre-set delay.
6.5 Blowing
Connect the suction hose (9) to the blow connector
(19) on the wet and dry vacuum cleaner.