Descargar
Compartir
Imprimir esta página
  1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 99-7010
  6. Instrucciones de instalación

Metra 99-7010 Instrucciones De Instalación

Mitsubishi eclipse/ eclipse spyder 2006-2012
Ocultar thumbs
1
2
3
4
5
6
7
8

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
INSTALLATION INSTRUCTIONS FOR PART 99-7010
Mitsubishi Eclipse/Eclipse Spyder 2006-2012
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• Double DIN radio provision
• Painted silver to match factory dash
KIT COMPONENTS
• A) Radio housing • B) ISO brackets • C) ISO trim plate • D) Double DIN bracket • E) Pocket
• F) Double DIN trim plate
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • MITO-01 - Mitsubishi amp interface 2006-up • 70-7001 - Mitsubishi 1992-up
Antenna Adapter: • Not required
TOOLS REQUIRED
• Phillips screwdriver • Small flat blade screwdriver
METRA. The World's best kits.
99-7010
C
D
1-800-221-0932
™
E
F
metraonline.com
Table of Contents
- Radio housing assembly....................................... 2
- DIN radio provision with pocket ............................ 3
- ISO DIN radio provision with pocket ...................... 3
- Double DIN radio provision ............................ (back)
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION

Publicidad

loading

Manuales relacionados para Metra 99-7010

Resumen de contenidos para Metra 99-7010

  • Página 1: Tabla De Contenido

    INSTALLATION INSTRUCTIONS FOR PART 99-7010 Table of Contents Mitsubishi Eclipse/Eclipse Spyder 2006-2012 99-7010 Dash Disassembly – Mitsubishi Eclipse/Eclipse Spyder 2006-2012 ..2 KIT FEATURES Kit Assembly • DIN radio provision with pocket • ISO DIN radio provision with pocket – Radio housing assembly........2 •...

  • Página 2: Dash Disassembly

    Dash Disassembly Kit Assembly Mitsubishi Eclipse/Eclipse Radio housing assembly Spyder 2006-2012 1. Clip the A/C vents into the 99-7010 1. Unclip and remove the trim panel radio housing. (Figure A) including the radio A/C vents. (Figure A) 2. Clip the hazard switch into the 99-7010 radio housing.

  • Página 3: Din Radio Provision With Pocket

    3. Snap the pocket into the kit. (Figure B) 4. Snap the pocket into the kit. (Figure B) 4. Locate the factory wiring harness in the dash. Metra recommends 5. Locate the factory wiring harness (Figure A) (Figure A) using the proper mating adapter in the dash.

  • Página 4: Double Din Radio Provision

    Metra recommends using the proper enrolling in the most recognized and respected mobile electronics school in our industry. mating adapter from Metra or AXXESS. Re- Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps connect the negative battery terminal and toward a better tomorrow.

  • Página 5: Componentes Del Kit

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7010 Indice Mitsubishi Eclipse/Eclipse Spyder 2006-2012 99-7010 Desmontaje del tablero – Mitsubishi Eclipse/Eclipse Spyder 2006-2012 ..2 CARACTERÍSTICAS DEL KIT Ensamble del kit • Provisión de radio DIN con bolsillo • Provisión de radio ISO DIN con bolsillo –...

  • Página 6: Desmontaje Del Tablero

    2. Quite los (4) tornillos Phillips que luces intermitentes en la carcasa sujetan el chasís del radio al tablero y retire. (Figura B) del radio 99-7010. (Figura B) 3. Desenganche y quite las rejillas del aire Continúa en la página (Figura B) acondicionado del panel de la moldura del radio de fábrica.

  • Página 7: Provisión De Radio Iso Din Con Bolsillo

    4. Ubique el arnés del cableado (Figura A) (Figura A) carcasa del radio. (Figure B) de fábrica en el tablero. Metra recomienda usar el adaptador de 5. Ubique el arnés del cableado acoplamiento adecuado de Metra de fábrica en el tablero. Metra recomienda usar el adaptador de o AXXESS.

  • Página 8: Provisión De Radio Doble Din

    INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7010 Provisión de radio doble DIN 1. Corte la costilla de la barra central. (Figure A) 2. Deslice el soporte correspondiente en la carcasa del radio, alineando los orificios de la carcasa con los orificios del soporte.