Descargar Imprimir esta página

Metra 99-7346B Instrucciones De Instalación

Hyundaielantra2011-2013

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Truss-head Phillips screws
A
B
Metra. The World's Best Kits.
®
Hyundai Elantra 2011-2013
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted black to match factory finish
C
D
MetraOnline.com
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
99-7346B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
–ISO DIN radio provision with pocket . .................3
–ISO DDIN radio provision . ....................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7304 • AX-HYKIA1-SWC
& AX-HYKIA-SPDIF (for amplified models)
Antenna Adapter: Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 4/26/18 INST99-7346B

Publicidad

loading

Resumen de contenidos para Metra 99-7346B

  • Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/26/18 INST99-7346B...
  • Página 2 DASH DISASSEMBLY 1. Remove trim panels from each side of center console. (Figure A) 2. Remove (4) Phillips screws from radio trim panel. Gently pry radio trim panel from dash. (Figure B) 3. Remove (4) Phillips screws securing radio chassis to sub dash. Disconnect and remove radio chassis. (Figure C) Continue to Kit Assembly (Figure A) (Figure B) (Figure C) 1.800.221.0932 MetraOnline.com...
  • Página 3 1. Secure the radio brackets to the radio with the (4) #8 x 3/8” Phillips screws with the screws included with radio. supplied. (Figure A) (Figure A) 2. Secure the radio to the bracket/pocket 2. Locate the factory wiring harness assembly with the screws included with and antenna plug in the dash. Metra the radio. (Figure A) recommends using the proper mating adapters from Metra and/or AXXESS. 3. Locate the factory wiring harness and antenna plug in the dash. Metra 3. Secure the assembly into the sub dash. recommends using the proper mating (Figure B) (Figure A) (Figure A) adapters from Metra and/or AXXESS. 4. Reassemble dash in reverse order of 4. Secure the assembly into the sub dash. disassembly using 99-7346B trim panel (Figure B) instead of factory panel. (Figure B) 5. Reassemble dash in reverse order of disassembly using the radio trim panel instead of factory panel. (Figure B) (Figure B) (Figure B) REV. 4/26/2018 INST99-7346B...
  • Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/26/18 INST99-7346B...
  • Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/26/18 INST99-7346B...
  • Página 6 DESMONTAJE DEL TABLERO 1. Quite los paneles de la moldura desde cada lado de la consola central. (Figura A) 2. Quite los (4) tornillos Phillips del panel de la moldura del radio. Quite con cuidado el panel de la moldura del radio del tablero. (Figura B) Quite los (4) tornillos Phillips que sostienen el chasís del radio al sub tablero. Desconecte y quite el chasís el radio. (Figura C) Continúe con el Ensamble del Kit (Figura A) (Figura B) (Figura C) 1.800.221.0932 MetraOnline.com...
  • Página 7 Provisión de radio ISO DIN con cavidad Provisión de radio ISO DDIN 1. Sujételo los soportes de radio en la 1. Sujételo los soportes de radio en la radio cavidad con los (4) tornillos Phillips #8 x con los tornillos que vienen con el radio. 3/8” suministrados. (Figura A) (Figura A) 2. Sujételo la radio en el ensamble 2. Ubique el arnés de cableado de fábrica soporte/cavidad con los tornillos y el conector de la antena en el tablero. incluidos con el radio. (Figura A) Metra recomienda que use adaptadores adecuados de acoplamiento de Metra 3. Ubique el arnés de cableado de fábrica y/o de AXXESS. y el conector de la antena en el tablero. 3. Sujételo el ensamble en el sub tablero. Metra recomienda que use adaptadores (Figura A) (Figura A) adecuados de acoplamiento de Metra (Figura B) y/o de AXXESS. 4. Vuelva a armar el tablero al revés de 4. Sujételo el ensamble en el sub tablero.
  • Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/26/18 INST99-7346B...