Virutex SRB165 Manual De Instrucciones página 17

saw blades can easily break.
• Do not saw ferrous metals. Red hot chips can ignite
the dust extraction.
• When working with the machine, always hold it fir-
mly with both hands and provide for a secure stance.
The power tool is guided more secure with both hands.
• Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
• Always wait until the machine has come to a com-
plete stop before placing it down. The tool insert can
jam and lead to loss of control over the power tool.
• Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
1.3 SAFETY INSTRUCTIONS FOR USE AND MAIN-
TENANCE OF THE BATTERY AND CHARGER
Do not store the tool and battery cartridge
in locations where the temperature may
reach or exceed 45° C.
Do not incinerate the battery cartridge.
Do not expose battery cartridge to water
or rain.
• Only recharge with the manufacturer's specified
charger. Only recharge with the manufacturer's speci-
fied charger. A charger which is suitable for one type
of battery cartridge can cause a fire risk on another
type of battery cartridge.
• Only use this power tool with the battery cartridge
specifically designed for this model. The use of other
types of battery cartridges may cause injury to the
operator and a fire risk.
• When the battery cartridge is not in use, keep it
away from metal objects, such as paper clips, coins,
keys, nails, screws or other small metal objects that
can establish
contact from one terminal to the other. Shorting the
battery terminals may cause burns or a fire.
• Battery fluid may be spilled under extreme condi-
tions; avoid contact with this liquid. In case of acci-
dental contact, rinse thoroughly with water. If the
liquid comes into contact with your eyes, seek medical
attention. Battery fluid may cause irritation or burns.
• Do not use damaged or modified batteries. Damaged
or modified batteries can behave in an unpredictable
way and may cause injury to the operator and a fire
risk.
• Avoid switching the device on accidentally. Make
sure the on/off switch is in the off position before in-
serting the battery. Carrying the power tool with your
finger on the on/off switch or inserting the battery
with the switch in the on position can cause accidents.
• Do not open the batteries. You could damage the
circuits.
• Fumes may be aired if there is battery damage and
improper use. In this case, go to a well-ventilated lo-
cation and seek medical assistance, if necessary. Fumes
cause respiratory irritation.
• When the battery is defective, the liquid may leak
and come into contact with adjacent components.
Check the corresponding parts. Clean or replace them,
if necessary.
• Protect the battery from heat, continued solar radia-
tion and fire. There is an explosion hazard.
Read all instructions and safety warnings.
• Protect the battery charger from rain and moisture.
Water entering the charger increases the risk of elec-
tric shock.
• Do not charge other batteries. The battery charger is
only suitable for charging lithium-ion batteries within
the indicated voltage range. Otherwise, there is a fire
and explosion hazard.
• Keep the battery charger clean. Dirt can cause a risk
of electric shock.
• Always check the battery charger, its cable and plug
before using them. Do not use the charger if you see
it is damaged. Do not open the charger on your own.
Have it repaired by a qualified person who uses origi-
nal spare parts. Damaged chargers, cables and plugs
increase the risk of electric shocks.
• Do not use the battery charger on highly flammable
surfaces. For example, paper, textiles, etc., or in com-
bustible environments. A fire hazard exists from the
charger heating during the charging cycle.
2. SPECIFICATIONS
Battery voltage.........................................................20 V Max
Battery type......................................................................Li-Ion
Time to charge battery..................................................60 min
Battery capacity..............................................................2 or 4 A
No-load speed.................................................4,800/min
Saw diameter.....................................................165 mm
Tooth thickness...............................................1,8 mm
Bore Ø of circular saw blade.......................................20 mm
Depth of cut at 90°..................................................54 mm
Depth of cut at 45°..................................................41 mm
h
-1
17