Dust Collection; Battery Maintenance - Virutex SRB165 Manual De Instrucciones

3. Parallel guide adjustment
For parallel cutting, use the parallel guide 28 (Fig. 1)
The cutting width is adjusted with the scale or according
to the plotting.
Tighten the wing bolt 21 to work with the parallel guide.
4. It possible to correct the alignment of saw blade
and the base at 90º by adjusting the position of screw
33 (Fig. 5). Turning the screw clockwise will reduce the
angle 90-, truning the screw anticlockwise will increase
the angle 90+.

11. DUST COLLECTION

Remove the battery from the power tool
before carrying out work on the power tool.
Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
This saw is equipped with a dust extraction adaptor N to
which the nozzle (optional accessory) 8204077 (Fig. 4)
can be connected together our standard dust collection
attachment ref. 6446073 (2.25 m) or 1746245 (5 m)
(optional accessories) to our dust collectors AS182K,
AS282K, ASM582T, ASC682 or to any industrial dust
collection system.
CAUTION: Always use a dust collector designed in accor-
dance with the applicable guidelines on sawdust emission.
12. MAINTENANCE
Remove the battery from the power tool
before carrying out work on the power tool.
- Check the saw blade. Deposits of resin and glue on
the saw blade cause inefficient cutting. To avoid them,
always clean the blade immediately after use.
- Inspect the mounting screws. Regularly inspect all the
mounting screws and ensure they are firmly tightened.
Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
- Motor maintenance. Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast
the motor regularly with compressed air.
- Check the lower guard for proper closing before each
use. Always keep it clean from chips and resin.
- Use only Virutex accessories and spares. Parts the chan-
ging of which is not showed in this instruction manual,
should be replaced in a Virutex official service centre.
20

13. BATTERY MAINTENANCE

Maintenance of the electric tool / preventive measures
Remove the battery from the power tool before carrying
out work on the power tool.
Battery maintenance instrucions
• Charge the battery cartridge 2 (Fig. 8) before com-
pletely discharged. Stop operation in low power and
charge it immediately.
• Do not overcharge when the battery is full, other-wise
it will shorten the life time.
• Charge the battery cartridge with room temperature
at 10° C - 40° C (50°F to 104°F). Charging the battery
in temperatures out of this range can damage it and
may cause fire.
• Charge battery every 6 months without operation
for a long time.
• Replace worn out batteries in time. Decline of pro-
duction or a significantlyshorter runtime of the power
tool after charging indicates aging of the battery and the
need for replacement. It should be taken into account
that the battery may discharge faster if the works take
place in the temperature below 0°.
• In case of long time storage without use, it is recom-
mended to store the battery at room temperature, it
should be charged to 50%.
Technical service:
a) To maintain product safety and reliability, repairs, any
other maintenance or adjustment should be performed
by authorized service senters, always using original
replacement parts.
b) Do not repair damaged batteries. Maintenance of the
batteries should be performed only by their producer or
authorized service center.
Transport of Li-Ion batteries
The contained Li-Ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepa-
ration of the item being shipped, consulting an expert
for hazardous material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations
14. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this device have
been measured in accordance with European standard
EN60745-2-5 and EN 60745-1 and serve as a basis for