Publicidad
Idiomas disponibles
Idiomas disponibles
FIGURE
8
_E_ELING
LEVEL!NG
//--
_,:©_
" _"_
_
":C
32 × ! 2
-C';G
j_'["
Sg_E,',
,1032
HEX
KEPS
_'_gT_'_'i
-_
.
:"
.::,
:..%
FLOOR
STAND
LEG
\
4',
\
9. Set the router
table top side down on the floor as
shown
in Figure 9. At this
stage
in the procedure,
employing
a second
person
to aid you in holding
the router
table
and the floor
stand
in place
is
strongly
recommended•
FIGURE
9
LOWER
• ,
,._
SHELF
,
.
_
-
:_r2OR
_<T-_'ID
LEG
•
i
•
•
*
--
:'0
32 _E: _, KEPS
NUT
."
.
T,,p_CL
L
),
//--:uPPER
SHELF
,_
t *
/
"".._
_
=:O 32 X i 2
LONG
-
/
TqUSS
HEAD
MACHh"4E
SC_E,',
• [
TYPICAL
_,
_
,,_
ROUTER
TABLE
LEG
ROCTEB
TABLE_
_
"_
S,',:TC
_
10. Position the floor stand on the router table legs,
as shown in Figure 9.
11. Set the upper shelf on the floor stand legs, as
shown in Figure 9.
12. Line up the holes in the floor stand leg and the
upper shelf with the corresponding holes in the router
table legs.
I
I
Inserting
a nail with a large head
I
NOTE
through one of the holes at each of the four corners
of the lower shelf will aid you in maintaining part
alignment.
(The truss head machine screws may
also be used.) The nails (or screws) are removed
from the holes when the truss head machine screws
are assembled as described in the next step.
It may be necessary,
to loosen
the fasteners
holding
the legs to the table
in order to make
the holes
in
table legs line up with the holes in the shelf and the
holes in the floor
stand
legs. and so the table legs
can be made to lie fiat on the floor
stand
legs.
13. Assemble
a ,_I0-32
x 1/2" long truss
head
machine
screw
and #10-32
hex "KEPS"
nut at each
of the holes,
as shown
in the Figure
9, Assembly
Detail.
ORIENTATION
OF THE FASTENERS
MUST
BE AS SHOWN.
FIGURE
9, ASSEMBLY
DETAIL
//./"
f'"
_
=_
12 _,
<E_a
-
-
._
//-
_ :.C._
_
• /
e
,
__-
..
.
.
UPPER
S_EL_
_
_LCOR
STANC
-E2_
_._f/
'¢_:-
".E _ Z:E.'.
:_E"-2_-
2--:
L
_E.2
14. SECURELY
TIGHTEN
ALL FASTENERS.
INCLUDING
THOSE
HOLDING
THE LEGS TO THE
ROUTER
TABLE.
15. Set the floor
stand
right side up on the floor, as
shown
in Figure
10.
FIGURE 10
16. Adjust the leveling feet by:
a. loosening the screws holding leveling bracket
to leg,
b. adjusting the height,
c. retightening the screws until the floor stand is
firmly supported by the floor and does not rock
back and forth.
17. It may be necessary
for you to do this any time
the floor stand
and router table are moved.
10
Publicidad
