Publicidad
Idiomas disponibles
Idiomas disponibles
TOOLS
REQUIRED
o Slotted
and Phillips
screwdriver.
, Small or medium
sized adjustable
wrench
(or a set of nutdrivers).
• Hammer•
ROUTER
TABLE
1. Lay the router table, top down. on a flat surface so
that the orientation of the table is as shown in Figure 1.
(BACK of the table is facing toward you.)
FIGURE 1
-
qOb-Eq
TABLE
/-_
"!0
32 X 1 2"
LONG
!
LEG
J
TRUSS
HEAD
MACHINE
/_
SCREW
(TYPICAL!
_J
_I0 32
HEX
KEPS
bIUT
•"
_
{TYPICALI
....
_
_. L_'-'.._ _,
....
j÷ i'
1
/
BACK
C:-
ROUTER
-&BLE
2. Assemble
a table leg to the table top using four
#10-32 x 1/2" long truss head machine screws and
four #10-32 hex "KEPS" nuts, as shown in Figure 1
and the Figure t, Assembly Detail. (Leg is shown in
the UPPER LEFT corner of router table.) DO NOT
TIGHTEN at this time.
3. Position the switch against the leg, as shown in
Figure 1, Assembly Detail.
4. Secure the switch to the leg and table top using
two #10-32 x 1/2" long truss head machine screws,
and two #10-32 hex "KEPS" nuts.
FIGURE 1, ASSEMBLY
DETAIL
_
10 32 X 1,2" LONG
TRUSS
HEAD
MACHINE
=/
SCREW
ITYPICAL)
'
\
--
ROUTER
TABLE
ROUTER
/!\
\
.
_
--
,10 32 HEX
"KEPS"
NUT
TABLE
LEG
_--
_
_
'
ITYP!CALI
MACHINE
_
---=- _ ......
:;-,
.
-
{,
"-
SCREW
NUT
"_
_'7;_" "_-1">
' :
":
(TYP
CALl
_ * -
_
:"
=
-"
"
_
....
f_
ASSEMB:_
v DETA'L
] There
are two hex shaped
]
NOTE
recesses
in the switch
case
into which
the hex
"KEPS" nuts are placed, with the toothed washer
side of the nuts facing out of the recesses.
5. Securely TIGHTEN all fasteners.
6. Assemble the remaining three table legs to the
table top using four #10-32 x 1/2" long truss head
machine
screws
and four #t0-32
hex "KEPS •' nuts
for each leg, as shown
in Figure
2. (The BACK of
the table is facing
toward
you.)
7. Securely TIGHTEN
all fasteners.
FIGURE 2
SWITCH
'\
RO_,-SR
--
T&BLE
_--=I032
_E_
KEU5
"
_--<----
" E_ _..'--"
....
7 :,_,/_
>_UT
-"=C'-
.
'"
DE,.
....1...---.:,
°
__
--
_10 32 X 1 2
LD_4G
ROUTER
&
BACK
OF
TABLE
TRUSS
HEAD
),!ACHtNE
ROUTER
TABLE
LEG
SCREW
T'r clCAL;
EXTENSIONS
TO THE ROUTER TABLE
1. Position the router table so that the orientation is
as shown in Figure 3 and Figure 3, Assembly Detail.
(FRONT of the table is facing toward you.)
2. Position one of the extensions
alongside the right
side of the table top so that the miter slot in the
extension lines up with the miter slot in table top.
3. Assemble a #10-32 x 1/2" long truss head
machine screw and a #10-32 hex "KEPS" nut at
each of the holes in the extension, as shown in
Figure 3 and Figure 3, Assembly Detail. DO NOT
FIGURE
3
_10 32
_EX
KEPE
!;_jT
--
--
ROL'-En
-- "10 32 X _ 2
LONG
ITYI_IB ALl
,+
-*t. RLE
_EG
TRUSS
HEAD
&4,mCHI_4E
--_
\
c-
-
\
SCREW
+TY_!CAL
,
/_
RIGHT
SIDE
.....
_'
/
EXTENS!ON
BR_CE
•
,_ f',.":--r---,_ .... ,_
__-
"-
EXTE tiSIOt't
,'
"
L.
_
'L
--
__
__"-
...... -_L .-'-t--
/_
EXTENSIOn,
BRACE
/
\_
'_ ,10 32 HEX
KECE
ROUTER
_--
S\%ITCH
--
%,
NUT
INOT
_lS BLEI
TABLE
_'1032X
12
LONG
'10 32 HEX
"KEPS
--z
TRUSS
HEAD
MACHI_4E
NUT
_NOT
_ IE!BLE
SCRE','v
Ib_OT VfSfBLE
Publicidad
