Technical Assistance - Legacy Levelwind Serie Manual De Instrucciones

5) Pull swivel assembly firmly from hose spool( SEE FIG. 13 and 14 ).
6) Unscrew Hose Clamp and pull hose off hose barb on swivel.
(SEE FIGURE 15)
7) Pull remaining length of hose out reel opening located at the reel
front.
8) Take replacement hose through opening located at the front of reel.
Thread hose through hose leveling mechanism. (SEE FIGURE 16)
9) Insert hose through the center of the hose spool. Four openings are
referenced with the following hose I.D. dimensions located at the
center of hose spool: 3/8 in., 1/2 in.,5/8 in. & 3/4 in.. Locate the
hose I.D. and pull through that opening. (SEE FIGURE 17) Pull
enough hose to allow the hose to connect to hose barb on swivel.
10) Replace hose onto hose barb, tighten hose clamp onto hose & place
swivel into hose spool housing.
11) Replace wear ring and fasten with wear ring screws. Replace wear
plate so that the swivel drive tabs insert into wear plate tab receivers.
(SEE FIGURE 18)
12) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
13) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
14) Remove screw driver.
15) Retract hose back into reel.
SWIvEL REPLacEMEnT
IMPORTANT: To ensure proper performance, please refer to the
Swivel Replacement Kit table to order the correct part number. Call
1(800) 645-8258 to order kit.
Swivel Kits
Part # Description
RP005007-38 Swivel Replacement kit for reel model L8305, L8305N,
L8305-EU, L8306, L8306-EU, L8310 & L8310-EU
RP005007-12 Swivel Replacement kit for reel model L8335, L8335-EU, L8345,
L8350 & L8350-EU
RP005007-58 Swivel Replacement kit for reel model L8344, L8346,
L8347 & L8349
1) Repeat steps 1- 6 in the HOSE REPLACEMENT procedure.
2) Place hose onto hose barb of new swivel body. Tighten hose clamp
onto hose & place swivel into hose spool housing.
3) Replace wear ring and fasten with wear ring screws. Replace wear
plate so that the swivel drive tabs insert into wear plate tab receivers.
(SEE FIGURE 18)
4) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
5) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
6) Remove screw driver.
7) Retract hose back into reel.
Troubleshooting
1) HOSE WILL NOT RETRACT
1a. Pull on hose, push latching switch to FreeRun mode.
Retract hose into reel.
1b. Spring is broken. Call service center.
2) HOSE WILL NOT FULLY RETRACT
2a. Spring tension too light?
2b. Replacement hose too heavy?
2c. Hose not retracting evenly? Is the Levelwind™
mechanism not working properly?
3) REEL WILL NOT LATCH
3a. Are you releasing hose too quickly?
3b. Broken latching pawl or mode switch?
4) REEL LEAKS
4a. Damaged hose?
4b. Loose fittings?
4c. Worn swivel seals?
Fig. 13
Fig. 15
Fig. 17

TEcHnIcaL aSSISTancE:

Call 800-645-8258 if you have any questions
regarding the installation or operation of this
reel.
3
Fig. 14
Fig. 16
Fig. 18